A pendulum is suspended from the ceiling of an elevator. When the elevator is at rest, the period is T. What happens to the period when the elevator is accelerating upward?

The number of turns in the solenoid is 10.08 x 10⁴.

Length of the solenoid, L = 0.5 m

Magnetic field, B = 9 T

Current flowing through the solenoid, I = 75 A

The magnetic field due to a current carrying solenoid,

B = μ₀NI/L

Therefore, the number of turns,

N = BL/μ₀I

N = (9 x 0.5)/(4[tex]\pi[/tex] x 10⁻⁷x 75)

N = 10.08 x 10⁴

To learn more about solenoid, click:

https://brainly.com/question/15504705

#SPJ4

This change affects the length of a month is a month gets longer.

As the moon moves away from the Earth and its orbit radius increases, its orbital period (the time it takes to complete one orbit around the Earth) also increases. This is because the force of gravity between the Earth and the Moon decreases with increasing distance, causing the Moon to move slower and take more time to complete each orbit.

Since a month is defined as the time it takes for the Moon to complete one orbit around the Earth, and the time for the Moon to complete one orbit is increasing, the length of a month is getting longer. Therefore, the correct answer is A) A month gets longer. However, the increase in the length of a month is very small, on the order of a few seconds per year, and is not noticeable in daily life.

To learn more about force of gravity visit: https://brainly.com/question/13634821

#SPJ11

The total distance that the springs in parallel are compressed is 5 cm.

Given information,

mass, m = 5kg,

The total distance that springs compressed, x = 10 cm

where x = x₁ + x₂,

the force exerted by the spring is given as

F = -k.x

The force exerted  by spring at series is,

Fs = - Ks(x₁ + x₂)

and,

F₁ = -K₁x₁

F₂ = -K₂x₂

Fs = F₁ = F₂,

equating values,

- Ks(x₁ + x₂) = -K₁x₁

since, x₁ = x₂ and K₁ = K₂,

Ks = K₁/2

Ks = 0.5K₁

Fs = - 0.5×K(x₁ + x₂)

The force exerted  by spring at parallel is,

Fp = F₁ +  F₂

Fp = -K₁x₁ + (-K₂x₂)

Fp  = -2K₁x₁

Equating,

Fs = Fp

- 0.5×K₁×10 = -2K₁x₁

x₁ = 2.5 cm

The total distance is,

2.5 + 2.5 = 5 cm

Hence, The springs in parallel are compressed by a total distance of 5 cm.

To learn more about Distance:

https://brainly.com/question/25361798

#SPJ12

The maximum resistance you can obtain by combining 570 −Ω , a 950 −Ω , and a 1.2 −kΩ  resistors is 2,720Ω.

To find the maximum resistance you can obtain by combining a 570Ω, a 950Ω, and a 1.2kΩ resistor, you should connect them in series. In a series connection, the total resistance is the sum of the individual resistances. Here's a step-by-step explanation:

1. Convert the 1.2kΩ resistor to Ω: 1.2kΩ = 1,200Ω
2. Connect the resistors in series: R_total = R1 + R2 + R3
3. Add the resistance values: R_total = 570Ω + 950Ω + 1,200Ω
4. Calculate the total resistance: R_total = 2,720Ω

The maximum resistance you can obtain by combining these resistors is 2,720Ω.

To learn more about resistance https://brainly.com/question/30924984

#SPJ11

Answer:

The answer is 0.8kg

Explanation:

Total mass =9kg

mass of object 1=4.5kg

mass of object 2=3.7kg

Tm=m1+m2+x

9=4.5+3.7+x

9=8.2+x

x=9-8.2

x=0.8kg

The potential energy stored in the spring is 2.5 joules.

The potential energy stored in a spring is given by the formula:

PE = (1/2)kx^2

where k is the spring constant and x is the displacement of the spring from its equilibrium position.

In this case, the force acting on the spring is 10 N, which is also equal to the spring's restoring force at its stretched position. Using Hooke's law, we can determine the displacement of the spring:

F = kx

x = F/k = 10 N / 20 N/m = 0.5 m

Now, we can calculate the potential energy stored in the spring:

PE = (1/2)kx^2 = (1/2)(20 N/m)(0.5 m)^2 = 2.5 J

Therefore, the potential energy stored in the spring is 2.5 joules.

To learn more about potential energy visit: https://brainly.com/question/24284560

#SPJ11

The negative sign indicates that the angular acceleration is in the opposite direction to the initial angular velocity (i.e., it is slowing down).

We can use the following formula to calculate angular acceleration:

α = (ωf - ωi) / t

where

ωi = initial angular velocity

ωf = final angular velocity

t = time interval

Here, the initial angular velocity ωi = 45.0 rad/s and the final angular velocity ωf = 10.0 rad/s, and the time interval t = 1.75 s.

Plugging in these values, we get:

α = (10.0 rad/s - 45.0 rad/s) / 1.75 s

α = -25.7 rad/s^2

The negative sign indicates that the angular acceleration is in the opposite direction to the initial angular velocity (i.e., it is slowing down).

To learn more about opposite visit:

https://brainly.com/question/29407794

#SPJ11

The correct option is (a) pull harder on the bucket than it pulls on you.

To lift a bucket of concrete, you must pull at a greater force than the force the bucket pulls on you. This is because the bucket of concrete is subject to the force of gravity, which pulls it downwards towards the Earth. In order to lift the bucket, you must apply a force greater than the force of gravity acting on the bucket.

According to Newton's third law of motion, every action has an equal and opposite reaction. This means that the bucket of concrete is pulling downwards on you with the same force that you are pulling upwards on the bucket. If your pulling force is greater than the force of gravity on the bucket, then the net force on the bucket will be upwards and the bucket will be lifted.

So the correct option is (a) pull harder on the bucket than it pulls on you.

To learn more about Newton's third law of motion visit: https://brainly.com/question/29768600

#SPJ11

Frequency-dependent wave summation and motor unit recruitment are both processes by which an increase in a stimulus can lead to an increase in muscle contraction.

Stimulus is a term used to describe any kind of external influence that can cause a change in behavior or thought. It is a broad term that can refer to a range of different events or stimuli, from physical objects to psychological stimuli. Stimulus can be either positive or negative, and can either cause an increase or decrease in behavior.

Frequency-dependent wave summation and motor unit recruitment are both processes by which an increase in a stimulus can lead to an increase in muscle contraction.

Frequency-dependent wave summation was achieved in the experiment by applying repetitive electrical stimulation to a muscle at increasing frequencies. The stimulation would cause a wave of depolarization to run through the muscle, resulting in a contraction. As the frequency of the stimulation increased, the strength of the contraction increased due to the summation of the waves.

Motor unit recruitment was achieved in the experiment by increasing the voltage of the stimulation. This would cause a stronger depolarization of the muscle and result in a stronger contraction. As the voltage of the stimulation was increased, the number of motor units recruited to contract the muscle would also increase.

In vivo, frequency-dependent wave summation is achieved by the nervous system sending signals to the muscle at increasing frequencies. This causes a wave of depolarization to run through the muscle, resulting in a stronger contraction.

In vivo, motor unit recruitment is achieved by the nervous system sending signals to the muscle at increasing voltage. This causes a stronger depolarization of the muscle, resulting in a stronger contraction. As the voltage of the signal increases, the number of motor units recruited to contract the muscle also increases.

To learn more about stimulus

https://brainly.com/question/1322236

#SPJ1

The substances listed in order of increasing boiling point (lowest first) are C2H6, CH3CHO, C2H5OH, and CH3COOH.

C2H6 is a non-polar molecule, meaning it has no permanent dipole moment. The intermolecular forces holding the molecules together are van der Waals' forces, which are weak and require the least amount of energy to overcome.

CH3CHO is a polar molecule due to the carbonyl group, which creates a permanent dipole moment. The intermolecular forces holding the molecules together are dipole-dipole forces, which are stronger than van der Waals' forces.

C2H5OH and CH3COOH are both polar molecules due to the presence of the hydroxyl group (-OH) and the carboxyl group (-COOH), respectively. The intermolecular forces holding the molecules together are hydrogen bonds, which are much stronger than dipole-dipole or van der Waals' forces.

The order of boiling points can be explained by the strength of the intermolecular forces. C2H6 has the weakest intermolecular forces, so it requires the least amount of energy to overcome them and boil. CH3CHO has stronger dipole-dipole forces than C2H6, so it requires more energy to boil. C2H5OH and CH3COOH both have hydrogen bonds, which are the strongest intermolecular forces, so they require the most energy to overcome and boil.

In summary, the boiling point depends on the intermolecular forces present, which are determined by the polarity of the molecule and its molecular mass. Polar molecules with hydrogen bonding have stronger intermolecular forces and higher boiling points.

For more such questions on Boiling point.

https://brainly.com/question/28203474#

#SPJ11

This technique is often used in forensic science to identify inks used in forged documents or other types of evidence.

One method to separate a mixture of colored inks is chromatography. Chromatography is a physical separation technique used to separate mixtures based on their molecular properties. In the case of colored inks, paper chromatography is a commonly used technique.

In paper chromatography, a small amount of the ink mixture is spotted onto a piece of chromatography paper, and the paper is placed in a container with a small amount of solvent (e.g. water, alcohol, or acetone). The solvent moves up the paper by capillary action, carrying the ink mixture with it. As the solvent moves up the paper, different components of the ink mixture are separated and are visible as colored bands.

The separation occurs because different components of the mixture have different affinities for the paper and the solvent. Components that are more soluble in the solvent will move up the paper more quickly, while those that are more attracted to the paper will move up more slowly. This results in a separation of the components based on their physical and chemical properties.

By comparing the separated bands of the ink mixture to those of known pure inks, the identity of each component in the mixture can be determined. This technique is often used in forensic science to identify inks used in forged documents or other types of evidence.

To learn more about chromatography visit:

https://brainly.com/question/30907934

#SPJ11

A likely method to separate a mixture of colored inks is through chromatography, a technique used to separate components of a mixture. It separates the ink into its constituent colors by allowing a solvent to travel up a stationary phase like paper, carrying the ink mixture with it.

A method that would likely be used to separate a mixture of colored inks is chromatography. Chromatography is a method used in chemistry to separate components of a mixture. It works by using a stationary phase and a mobile phase. In the case of ink separation, the ink mixture would be placed on a stationary phase (like paper), and a solvent (the mobile phase) would be allowed to travel up the paper. As the solvent travels, it moves the mixture along its path. Each component of the ink by their size, chemical properties, and interaction with the solvent and paper will move at different rates, thereby separating the ink into its constituent colors. This method is particularly useful in analyzing the chemical composition of inks and other similar mixtures.

https://brainly.com/question/34281753

#SPJ12

a. The overall displacement Δx of the particle is 75 m to the east.

b. The average velocity vav of the particle over the time interval Δt=50.0s is 1.5 m/s to the east.

c. To find the instantaneous velocity v of the particle at t=10.0s, we can calculate the derivative of the position function x(t) with respect to time t at t=10.0s.

From the given position function x(t) = 0.25t³ - 1.5t² + 3t, we can find the velocity function v(t) by taking the derivative: v(t) = dx/dt = 0.75t² - 3t + 3. At t=10.0s, the instantaneous velocity v of the particle is v(10.0) = 57.0 m/s to the east.

The displacement of the particle can be found by subtracting its initial position from its final position, which gives Δx = x(60.0s) - x(10.0s) = 3000 m - 2925 m = 75 m to the east. The average velocity of the particle over the time interval is given by the formula vav = Δx/Δt = 75 m/50.0 s = 1.5 m/s to the east.

Finally, the instantaneous velocity of the particle at t=10.0s can be found by taking the derivative of the position function x(t) with respect to time t and evaluating it at t=10.0s, giving the value of the velocity at that instant.

To learn more about average velocity, here

https://brainly.com/question/862972

#SPJ4

Calculations of displacement, average velocity, and instantaneous velocity require specific information about the motion of the particle. Each of these calculations can be performed using calculus when the motion of the particle is defined as a function of time.

The questions are about the interpretation of the motion and the velocity of a particle. However, the actual values, for displacement Δx, average velocity vav, and instantaneous velocity v, could not be directly calculated without additional specific information about the motion of the particle. But here's a general method:

a. The overall displacement, Δx, of the particle can be calculated by integrating the velocity function, v(t), over the time interval.

b. The average velocity, vav, of a particle over a time interval, Δt, can be found by dividing the total displacement, Δx, by the total time, Δt.

c. The instantaneous velocity, v, of a particle at a specific time, t, can be calculated by taking the derivative of the position function, x(t), at that time.

https://brainly.com/question/32276534

#SPJ11

An axon requires three pieces of information to calculate the current associated with an NCV pulse: potential, resistance per unit length, and length. So, the correct answer is option D.

Potential is the difference in voltage between two places, while resistance per unit length is the amount of resistance present along an axon's length.

The voltage difference is multiplied by the axon resistance to determine the current. By dividing the resistance per unit length by the axon's length, the resistance of the axon is determined.

We can determine the current associated with an NCV pulse by knowing the potential, resistance per unit length, and length of an axon.

Complete Question:

What information about an axon is required to calculate the current associated with an NCV pulse?

A. Conductivity, resistivity, and length

B. Potential, conductivity, and radius

C. Potential, resistivity, and radius

D. Potential, resistance per unit length, and length

To learn more about axon visit:

https://brainly.com/question/25818094

#SPJ4

Beam A has twice as many photons hitting a given area in a given time as beam B.

The energy of a photon is given by E = hf, where h is Planck's constant and f is the frequency of the light. The frequency is related to the wavelength by f = c/λ, where c is the speed of light.

Therefore, the energy of a photon can also be expressed as E = hc/λ.

The intensity of light is the power per unit area, and is given by I = P/A, where P is the power of the light and A is the area that it illuminates.

If beam A has twice the wavelength but the same intensity as beam B, this means that they have the same power per unit area. That is,

I(A) = I(B) = P/A

Since the power per unit area is the same, the number of photons that hit a given area in a given time must also be the same for both beams.

The number of photons is given by the energy of the light divided by the energy of a single photon:

N = P/(hc/λ)

Since the power per unit area is the same for both beams, and the speed of light is constant, we can write:

N(A) = P/(hc/2λ) = 2P/(hc/λ) = 2N(B)

Therefore, beam A has twice as many photons hitting a given area in a given time as beam B.

To learn more about energy visit:

https://brainly.com/question/1932868

#SPJ11

In a gas mixture with the same temperature, lighter particles move faster and heavier particles move slower.

If a gas mixture has the same temperature, the lighter particles will move faster and the heavier particles will move slower. This is because the kinetic energy of the gas particles is directly proportional to their mass and temperature, according to the kinetic theory of gases.

Lighter particles have less mass and therefore require less kinetic energy to move at a faster speed compared to heavier particles, which have more mass and require more kinetic energy to move at the same speed. As a result, the lighter particles will move faster and collide more frequently with other particles in the gas mixture, while the heavier particles will move slower and collide less frequently.

Learn more about kinetic theory of gases

brainly.com/question/30648725

#SPJ11

Diffraction of light is defined as the phenomenon where the bending of light happens around corners such that it spreads out and illuminates areas where the formation of shadow is expected.

Here diffraction grating, is defined as an optical element that divides the light into various wavelengths.

The formula for diffraction is: dsinФ=nλ

where, d is the distance between the slits, Ф is the diffracting angle, n is the order number and λ is the wavelength.

Given, grating is 2090 grooves per centimeter for n=1,

d=n/λ

Then,

d = 1 × 10⁻² / 1990  = 5.025 × 10⁻⁶ m

sinФ=nλ/d

1 × 640 × 10⁻⁹ /  5.025 × 10⁻⁶  = 0.127

Ф = Sin⁻¹ ( 0.127) = 7.29 degrees

To know more about diffraction grating, visit;

https://brainly.com/question/28205086

#SPJ4

The new period of oscillation will be 2π√(m/((n + 1)k)).

When identical springs are added in parallel to the original glider, the effective spring constant of the system increases. This is because the springs are now acting together to produce a greater force, and thus the restoring force on the glider is greater than before.

As a result, the period of the oscillation will decrease. The period of oscillation for a mass-spring system is given by:

T = 2π√(m/k)

Where T is the period, m is the mass of the glider, and k is the spring constant. Since the mass of the glider does not change when additional springs are added in parallel, the period will decrease due to the increase in the effective spring constant (k_eff).

The effective spring constant of the system with n identical springs in parallel is given by:

k_eff = (n + 1)k

Therefore, the new period of oscillation will be:

T' = 2π√(m/(k_eff))

= 2π√(m/((n + 1)k))

Since k_eff > k, T' < T, which means that the period of oscillation will decrease when identical springs are added in parallel to the original glider.

for such more question on oscillation

https://brainly.com/question/12622728

#SPJ11

The change in volume of the piston when the work done is 1000 J and the pressure is a constant 1000 Pa, is 1 m³.

To find the change in volume of the piston you can use the following formula:

Work Done = Pressure × Change in Volume

Here, Work Done = 1000 J, and Pressure = 1000 Pa.

So, the change in volume of the piston is 1 m³ ,when the work done is 100OJ.

for more information on work done by piston : https://brainly.com/question/30352788

#SPJ11

The potential energy of the system when the object displacement is 0.040 m, exactly half the maximum amplitude, is 0.024 J.

When an object is oscillating on a spring, it has both kinetic and potential energy. The potential energy of the system is stored in the spring and is a function of the displacement of the object from its equilibrium position. In this case, the object has a mass of 0.20 kg and is oscillating on a spring with a spring constant of k = 15 N/m.

To calculate the potential energy of the system when the object displacement is 0.040 m, exactly half the maximum amplitude, we first need to determine the amplitude of the oscillation. The amplitude is the maximum displacement from the equilibrium position, and in this case, it is twice the displacement of 0.040 m, or 0.080 m.

The potential energy of the system is given by the formula U = 1/2 [tex]kx^2[/tex], where k is the spring constant and x is the displacement from the equilibrium position. Plugging in the values, we get:

U = 1/2 (15 N/m) [tex](0.040 m)^2[/tex]
U = 0.024 J

For more such questions on Potential energy.

https://brainly.com/question/30147894#

#SPJ11

The drift velocity (v) of charge carriers in a conductor is given by the following equation: v = I / (n [tex]\times[/tex] A [tex]\times[/tex] q).

v = I / (n [tex]\times[/tex] A [tex]\times[/tex] q)

where:

v is the drift velocity, measured in meters per second (m/s)

I is the current flowing through the conductor, measured in amperes (A)

n is the number of charge carriers per unit volume of the conductor, measured in per cubic meter ([tex]m^(-3)[/tex])

A is the cross-sectional area of the conductor, measured in square meters (m^2)

q is the charge of a single carrier, such as an electron, measured in coulombs (C)

This equation relates the drift velocity of the charge carriers to the current flowing through the conductor, the number of charge carriers per unit volume, the cross-sectional area of the conductor, and the charge of a single carrier. The drift velocity represents the average velocity of the charge carriers as they move through the conductor in response to an applied electric field.

The number of charge carriers per unit volume (n) depends on the material of the conductor and the temperature. In metals, the charge carriers are typically electrons, and the number density is on the order of 10^28 to 10^29 electrons per cubic meter.

The cross-sectional area (A) of the conductor is the area of the cross-section of the conductor perpendicular to the direction of the current flow, and is a measure of the amount of material available for the charge carriers to move through.

The charge of a single carrier (q) is typically the charge of an electron, which is approximately 1.6 x [tex]10^{-19[/tex] coulombs.

To learn more about drift velocity visit: https://brainly.com/question/4269562

#SPJ11

The cosmic background radiance consists of electromagnetic radiation in the microwave part of the spectrum that fills all space. It is a landmark evidence of the Big Bang theory for the origin of the universe.

After conducting studies to identify microwave radiation coming from Milky Way sources, Arno Penzias and Robert Wilson made the initial discovery of the CBR in 1964. But, they discovered that, for reasons they could not understand, their instrument was picking up a steady signal from all directions. Later, this signal was recognized as the CBR, which is assumed to be the lingering radiation from the Big Bang (BB). 

Scientists were able to determine the age of the universe, which is thought to be roughly 13.8 billion years old, by measuring the temperature of the CBR. Also, it aided in the identification of the components of the universe, which are roughly 5% ordinary matter, 27% dark matter, and 68% dark energy. It also proposes that the Universe started out in a hot, dense state and has been expanding and cooling ever since, providing support for the BB Theory.

To know more about Cosmic Background Radiation visit:

https://brainly.com/question/28197648

#SPJ1

The ratio of the potential energy of Satellite B to Satellite A is 2/3. This means that Satellite B has about 67% of the potential energy of Satellite A.

To calculate the ratio of the potential energy of Satellite B to Satellite A, we need to use the formula for gravitational potential energy:

U = [tex]- G (m_1m_2)/r[/tex]

where U is the gravitational potential energy, G is the gravitational constant ([tex]6.67 \times 10^{-11}\: Nm^2/kg^2[/tex]), [tex]m_1[/tex] and [tex]m_2[/tex] are the masses of the two satellites, and r is the distance between them.

Since both satellites have the same mass, we can simplify the formula to:

U = [tex]- G m^2 / r[/tex]

where m is the mass of each satellite.

The distance between the center of Earth and Satellite A is RE, so the distance between Satellite A and Earth's center is (RE + RE) = 2RE. Similarly, the distance between the center of Earth and Satellite B is (2RE + RE) = 3RE.

So, the ratio of the potential energy of Satellite B to Satellite A is:

[tex]U_B / U_A = (- G m^2 / 3RE) / (- G m^2 / 2RE)[/tex]

Simplifying this expression, we get:

[tex]U_B / U_A = 2/3[/tex]

For similar question on potential energy

https://brainly.com/question/1242059

#SPJ11

Before the child begins any outward radial movement, the angular momentum of the system of child and turntable is zero.

What is the angular momentum of the child-turntable system before any outward radial movement?

The conservation of angular momentum concept can be used to determine the angular momentum of the child and turntable system before the child begins any outward radial movement.

Assuming the turntable is initially at rest and the child is sitting at a distance R from the axis of rotation of the turntable, the angular momentum of the system is given by:

L = Iω

where L denotes angular momentum, I denotes moment of inertia, and denotes angular velocity.

Since the child is treated as a point mass, its moment of inertia can be approximated as:

Ichild = mchild × R^2

Since the turntable is initially at rest, its initial angular velocity is zero:

ωinitial = 0

As a result, the system's initial angular momentum is:

Linitial = Ichild × ωinitial = 0

As a result, the angular momentum of the child-turntable system is zero before the child begins any outward radial movement.

To learn more about angular momentum, visit: https://brainly.com/question/4126751

#SPJ1

The total mechanical energy is conserved and is mgh.

At the height h, the energy in the ball is its potential energy and the kinetic energy of the ball at the height is zero.

Potential energy, PE = mgh

Kinetic energy, KE = 0

So, total mechanical energy, TE = KE + PE

TE = mgh

As the ball is moving, the potential energy will be converted to its kinetic energy.

mgh = 1/2mv²

v = √2gh

When it reaches the ground, the energy of the ball is kinetic energy and potential energy is zero.

KE = 1/2 mv² = mgh

PE = 0

TE = mgh

To learn more about mechanical energy, click:

https://brainly.com/question/13799884

#SPJ4

A typical raindrop would take 500 seconds

To calculate the time it takes for a raindrop to fall to the ground, we can use the formula: time = distance / speed. The terminal velocities for different raindrop sizes are approximately:

- Large raindrop (5 mm): 9 m/s
- Typical raindrop (2 mm): 6 m/s
- Drizzle drop (0.5 mm): 2 m/s

Assuming the cloud base is at 3000 meters, we can calculate the time for each type of raindrop as follows:

Large raindrop (5 mm): time = 3000m / 9 m/s = 333.33 seconds
Typical raindrop (2 mm): time = 3000m / 6 m/s = 500 seconds
Drizzle drop (0.5 mm): time = 3000m / 2 m/s = 1500 seconds

So, a large raindrop would take about 333.33 seconds to reach the ground,A normal raindrop takes 500 seconds to form., and a drizzle drop would take 1500 seconds to fall from the cloud base at 3000 meters to the ground when the air is still.

Learn more about terminal velocities.

brainly.com/question/2654450

#SPJ11

(a) The angular speed of the lazy susan after the cockroach stops is 2.20 rad/s.

(b) The mechanical energy of the system is not conserved as the cockroach stops

(a) To solve for the angular speed of the lazy susan after the cockroach stops, we can use the conservation of angular momentum, which states that the total angular momentum of a system is conserved in the absence of external torques. Initially, the angular momentum of the system (lazy susan and cockroach) is:

L_i = I * w_i + m * r * v

where I is the rotational inertia of the lazy susan, w_i is its initial angular velocity, m is the mass of the cockroach, r is the radius of the lazy susan, and v is the velocity of the cockroach relative to the ground.

Since the cockroach is running counterclockwise and the lazy susan is turning clockwise, their angular momenta have opposite signs, so we can use the convention that counterclockwise angular momenta are positive and clockwise ones are negative. Thus, the initial angular momentum of the system is:

L_i = - I * w_i + m * r * v

Substituting the given values, we get:

L_i = - (5.0 x 10⁻³ kgm²) * (2.8 rad/s) + (0.17 kg) * (0.15 m) * (2.0 m/s)

L_i = -0.0196 kgm²/s

When the cockroach stops, its velocity becomes zero, so the angular momentum of the system is conserved and becomes:

L_f = I * w_f

where w_f is the final angular velocity of the lazy susan. Equating the initial and final angular momenta, we get:

L_i = L_f

(5.0 x 10⁻³ kgm²) * (2.8 rad/s) + (0.17 kg) * (0.15 m) * (2.0 m/s) = (5.0 x 10⁻³ kgm²) * w_f

Solving for w_f, we get:

w_f = 2.20 rad/s

Therefore, the angular speed of the lazy susan after the cockroach stops is 2.20 rad/s.

(b) To determine whether mechanical energy is conserved as the cockroach stops, we can calculate the initial and final kinetic energies of the system. Initially, the kinetic energy of the system is:

K_i = (1/2) * I * w_i² + (1/2) * m * v²

Substituting the given values, we get:

K_i = (1/2) * (5.0 x 10⁻³ kg*m²) * (2.8 rad/s)² + (1/2) * (0.17 kg) * (2.0 m/s)²

K_i = 0.155 J

When the cockroach stops, its kinetic energy becomes zero, so the final kinetic energy of the system is:

K_f = (1/2) * I * w_f²

Substituting the calculated value of w_f, we get:

K_f = (1/2) * (5.0 x 10⁻³ kg*m²) * (2.20 rad/s)²

K_f = 0.027 J

Therefore, the mechanical energy of the system is not conserved as the cockroach stops, since there is a decrease in kinetic energy from 0.155 J to 0.027 J.

This decrease in kinetic energy is due to the work done by the frictional force between the cockroach and the lazy susan, which causes the cockroach to stop.

Learn more about angular momentum

brainly.com/question/30656024

#SPJ11

The nucleus n,mX is 17,8X. Based on the atomic number (m = 8), the element is oxygen. Therefore, the nucleus is 17,8O (oxygen-17). The nuclear reaction is 14,7N + 4,2He = 17,8O + 1,1H.

In the given nuclear reaction:
14,7N (nitrogen-14) + 4,2He (helium-4) = n,mX + 1,1H (hydrogen-1)

First, let's analyze the conservation of mass and atomic numbers in the nuclear reaction. To do this, we add the mass numbers (the top numbers) and the atomic numbers (the bottom numbers) on each side of the equation.

Mass numbers:
14 (N) + 4 (He) = n (X) + 1 (H)
18 = n + 1

Atomic numbers:
7 (N) + 2 (He) = m (X) + 1 (H)
9 = m + 1

Now, we can solve for n and m:
n = 18 - 1 = 17
m = 9 - 1 = 8

Learn more about conservation of mass here:

brainly.com/question/13383562

#SPJ11

When the two steel balls touch, charge is transferred between them until they reach equilibrium.

Since they are identical, we can assume that an equal amount of charge is transferred from the positively charged ball to the negatively charged ball.

To calculate the amount of charge transferred, we can use the formula:

Q = CV

Where Q is the charge transferred,

C is the capacitance of the system (which we assume to be constant), and

V is the potential difference between the two balls before they touch.

Since the balls have different charges, the potential difference between them is:

V = (charge of ball 1)/(capacitance of system) - (charge of ball 2)/(capacitance of system)

V = (-9 μC)/(C) - (28 μC)/(C) = -37 μC/C

When the balls touch, charge is transferred until they reach the same potential. The total charge before and after touching must be conserved, so we can set up the equation:

-9 μC + 28 μC = final charge on both balls

Simplifying, we get:

19 μC = final charge on both balls

Therefore, both balls will have a final charge of +19 μC.

To know more about equilibrium here

https://brainly.com/question/30807709

#SPJ11

If the mass is now replaced with one that has a value of 4M and the spring is again pulled back a distance X, force of the spring is four times.

Simple harmonic motion is a specific kind of periodic motion of a body that arises from a dynamic equilibrium between an inertial force that is proportional to the body's acceleration away from the static equilibrium position and a restoring force on the moving object that is directly proportional to the magnitude of the object's displacement and acts towards the object's equilibrium position. Oscillating spring perform SHM.

Force applied on the spring is spring constant times distance.

For system 1,

m = m

x = x

F = mx

for system 2,

m = 4m

x=x

F' = 4mx

looking at both the systems,

F' = 4F

Hence force of the spring will be 4 times.

To know more about Spring :

brainly.com/question/14670501

#SPJ4.