The total electric field strength along the line connecting the midpoints of a charged glass and plastic rod decreases with distance and is directed towards the plastic rod at distances of 2.0 cm and 3.0 cm.
The negative sign in E1', E2', and E3' indicates that the electric field created by the plastic rod is in the opposite direction to that of the glass rod.
To find the total electric field at each distance, we can use the principle of superposition, which states that the total electric field at a point is the vector sum of the electric fields created by each charged object at that point.
At each distance, the direction of the electric field created by the glass rod is the same, while the direction of the electric field created by the plastic rod is opposite. Therefore, the total electric field E1 to E3 along the line connecting the midpoints of the two rods is given by:
E1 = E1' + E = 0
E2 = E2' + E = -4.86 x 10³ N/C
E3 = E3' + E = -1.61 x 10³ N/C
where E is the electric field created by the glass rod alone.
Thus, at a distance of 1.0 cm from the glass rod along the line connecting the midpoints of the two rods, the total electric field is zero. At distances of 2.0 cm and 3.0 cm, the total electric field is directed towards the plastic rod and decreases in magnitude as the distance increases.
Learn more about electric field strength at
https://brainly.com/question/15170044
#SPJ4
The question is -
A 10-cm-long thin glass rod uniformly charged to 7.00 nC and a 10-cm-long thin plastic rod uniformly charged to -7.00 nC are placed side by side, 4.20 cm apart. What are the electric field strengths of E1 to E3 at distances 1.0 cm, 2.0 cm, and 3.0 cm from the glass rod along the line connecting the midpoints of the two rods?
a common source of wave motion is a wave pattern. harmonic object. region of variable high and low pressure. vibrating object. none of these
A common source of wave motion is a vibrating object, which creates a wave pattern that propagates through a region of variable high and low pressure.
This pattern can also be described as a harmonic pattern, as the vibrations are typically periodic and create a series of harmonics. Therefore, the correct answer is: vibrating object. When an object vibrates, it creates disturbances in the surrounding medium, which then propagate as waves. The wave pattern and regions of variable high and low pressure are a result of this vibrating object. Harmonic objects can also create wave motion, but they are not the only source.
More on waves: https://brainly.com/question/9959395
#SPJ11
Two points are located 4.2 m apart. If the potential difference between the two points is 44.4 V, what is the electric field (in V/m) between the points?
To find the electric field between the two points, we can use the formula. So, the electric field between the two points is approximately 10.57 V/m.
Electric field = Potential difference / Distance between the points
Plugging in the given values, we get:
Electric field = 44.4 V / 4.2 m
Electric field = 10.57 V/m
Therefore, the electric field between the two points is 10.57 V/m.
To find the electric field between two points with a potential difference, you can use the formula:
Electric Field (E) = Potential Difference (V) / Distance (d)
In this case, the two points are 4.2 meters apart and the potential difference between them is 44.4 V. Plugging these values into the formula, we get:
E = 44.4 V / 4.2 m
E ≈ 10.57 V/m
So, the electric field between the two points is approximately 10.57 V/m.
Visit here to learn more about electric field:
brainly.com/question/15800304
#SPJ11
the pulse strength (amplitude) should be rated on what scale
The pulse strength or amplitude can be rated on a scale of 0-10, with 0 being no pulse felt and 10 being the strongest possible pulse. This scale is commonly used in medical settings to assess the strength and regularity of a patient's pulse.
A weak pulse may indicate a problem with circulation or heart function, while a strong pulse may be a sign of hypertension or other cardiovascular issues. It is important to accurately rate the pulse strength to help diagnose and treat these conditions.
When assessing the pulse, it is important to take into account any factors that may affect the reading, such as the patient's age, physical activity level, or medication use. The pulse should also be evaluated at different points in the body, such as the wrist, neck, or ankle, to ensure an accurate assessment of overall cardiovascular health.
Overall, the pulse strength scale is a useful tool for healthcare providers to quickly and accurately assess a patient's cardiovascular function and detect any potential problems that may require further evaluation or treatment.
Know more about cardiovascular here:
https://brainly.com/question/27441596
#SPJ11
Eight identical bulbs are connected in series across a 120-V line.
What is the voltage across each bulb?
The voltage across each identical bulb connected in series across a 120-V line is 15 volts.
To find the voltage across each bulb when eight identical bulbs are connected in series across a 120-V line, follow these steps:
1. Determine the total voltage across the series circuit. In this case, it's given as 120 volts.
2. Since the bulbs are identical and connected in series, the total voltage will be divided equally across each bulb.
3. Divide the total voltage by the number of bulbs to find the voltage across each bulb.
So, the voltage across each bulb is 120 V (total voltage) / 8 (number of bulbs) = 15 V.
The voltage across each identical bulb connected in series across a 120-V line is 15 volts.
To learn more about voltage https://brainly.com/question/13368488
#SPJ11
why is it incorrect to say that when a hot object warms a cold one, the increase in temperature of the cold one is equal to the decrease in temperature of the hot one? when is this statement correct?
It is incorrect to say that when a hot object warms a cold one, the increase in temperature of the cold one is equal to the decrease in temperature of the hot one, because heat transfer depends on various factors, including the masses and specific heat capacities of the objects.
Specific heat capacity is the amount of heat required to raise the temperature of a substance by one degree Celsius. Different materials have different specific heat capacities, which means they need different amounts of heat to increase their temperature.
When two objects with different specific heat capacities come into contact, the heat transfer between them will depend on their specific heat capacities and masses. Consequently, the change in temperature for each object may not be equal. In some cases, the hot object might lose more heat than the cold object gains, or vice versa.
The statement would be correct only if the objects have equal masses and specific heat capacities. In this specific scenario, the amount of heat lost by the hot object would equal the amount of heat gained by the cold object, resulting in equal changes in temperature. However, this situation is relatively uncommon, making the general statement incorrect.
For more such questions on Heat transfer.
https://brainly.com/question/16084179#
#SPJ11
Suppose two parallel-plate capacitors have the same charge Q, but the area of capacitor 1 is A and the area of capacitor 2 is 2A.if the spacing between the plates in capacitor 1 is d what should the spacing between the plates in capacitor 2 be to make the capacitance of the two capacitors =
The spacing between the plates in capacitor 2 should be twice the spacing in capacitor 1 to make the capacitance of the two capacitors equal.
The capacitance of a parallel-plate capacitor is given by:
C = εA/d
where C is the capacitance, ε is the permittivity of free space, A is the area of the plates, and d is the distance between them.
For capacitor 1, the capacitance is:
C1 = εA/d
For capacitor 2, the capacitance is:
C2 = ε(2A)/x
where x is the spacing between the plates in capacitor 2.
Since the two capacitors have the same charge, we can set C1 = C2 and solve for x:
C1 = C2
εA/d = ε(2A)/x
x = 2d
Therefore, the spacing between the plates in capacitor 2 should be twice the spacing in capacitor 1 to make the capacitance of the two capacitors equal.
To learn more about permittivity visit: https://brainly.com/question/30403318
#SPJ11
an athlete runs with velocity 12 km/h for 5 minutes, 14 km/h for the next 4 minutes, and 18 km/h for other 6 minutes. compute the total distance traveled.
The athlete traveled a total distance of 3732.16 meters.
To find the total distance traveled, we need to calculate the distance traveled during each time interval and then add them up.
First, we need to convert the velocities from km/h to m/s, since distance is measured in meters and time is measured in seconds:
12 km/h = (12/3.6) m/s = 3.33 m/s
14 km/h = (14/3.6) m/s = 3.89 m/s
18 km/h = (18/3.6) m/s = 5.00 m/s
Now we can calculate the distances traveled during each time interval:
Distance traveled at 3.33 m/s for 5 minutes = (3.33 m/s)(5 min)(60 s/min) = 1000 m
Distance traveled at 3.89 m/s for 4 minutes = (3.89 m/s)(4 min)(60 s/min) = 932.16 m
Distance traveled at 5.00 m/s for 6 minutes = (5.00 m/s)(6 min)(60 s/min) = 1800 m
Finally, we can add up the distances to get the total distance traveled:
Total distance traveled = 1000 m + 932.16 m + 1800 m = 3732.16 m
Therefore, the athlete traveled a total distance of 3732.16 meters.
To learn more about athlete visit:
https://brainly.com/question/17404705
#SPJ11
for most materials, electrical conductivity only depends on the overall mobility of free electrons. question 2 options: true false
The statement "electrical conductivity only depends on the overall mobility of free electrons" is True because how rapidly and easily these electrons can travel through a material in response to an electric field determines the substance's electrical conductivity. .
Electrical conductivity in most materials is primarily determined by the mobility of free electrons, which refers to how easily and quickly these electrons can move through the material in response to an electric field.
Other factors such as the density of free electrons and the presence of impurities or defects can also affect conductivity, but mobility is a key factor.
Therefore, the statement electrical conductivity only depends on the overall mobility of free electrons is true.
Learn more about "mobility": https://brainly.com/question/25700682
#SPJ11
What is the deBroglie wavelength (in nm) of a neutron (m = 1.67*10-27 kg) moving with a speed of 24 m/s?
The deBroglie wavelength (in nm) of a neutron (m = 1.67*[tex]10^{-27[/tex] kg) moving with a speed of 24 m/s is 165 nm.
The de Broglie wavelength (λ) represents the wave-like behavior of particles and is particularly important in quantum mechanics. It can be calculated using the de Broglie equation:
λ = h / (m*v)
where λ is the de Broglie wavelength, h is the Planck constant (6.626 * [tex]10^{-34[/tex] Js), m is the mass of the particle, and v is its velocity.
In this case, we are given the mass of a neutron (m = 1.67 * [tex]10^{-27[/tex] kg) and its speed (v = 24 m/s). Plugging these values into the de Broglie equation, we get:
λ = (6.626 * [tex]10^{-34[/tex] Js) / ((1.67 * [tex]10^{-27[/tex] kg) * (24 m/s))
After performing the calculation, we find that the de Broglie wavelength is approximately 1.65 * [tex]10^{-10[/tex] meters. To convert this value to nanometers, we multiply by [tex]10^9[/tex] (since 1 meter equals [tex]10^9[/tex] nanometers):
λ ≈ 1.65 * [tex]10^{-10[/tex] meters * [tex]10^9[/tex] nm/meter = 165 nm
Thus, the de Broglie wavelength of a neutron moving at 24 m/s is approximately 165 nm. This demonstrates the wave-particle duality nature of subatomic particles, as the neutron exhibits both particle-like properties (mass and velocity) and wave-like properties (wavelength).
For more such questions on deBroglie wavelength.
https://brainly.com/question/13095392#
#SPJ11
Which artifact is not related to the unexpected reflection of an acoustic wave ?
a. multipath
b. comet tail
c. reverberation
d. lateral resolution
The artifact that is not related to the unexpected reflection of an acoustic wave is: d. lateral resolution
Lateral resolution refers to the ability to distinguish two closely spaced objects as separate entities in an image, while artifacts a, b, and c (multipath, comet tail, and reverberation) are related to unexpected reflections of acoustic waves. Lateral resolution is the image generated when the two structures lying side by side are perpendicular to the beam. This is directly related to the width of the ultrasound beam. The narrower the beam better is the resolution. The width of the beam is inversely related to the frequency.
Learn more about ultrasound here: https://brainly.com/question/30363405
#SPJ11
If 2 springs are stretched different amounts by the same mass hung from them, which spring has the larger spring constant, the one that stretches most or the one that stretches the least? Explain.
If 2 springs are stretched by different amounts by the same mass hung from them, the one that stretches the least has the larger spring constant.
To determine which spring has the larger spring constant when 2 springs are stretched by different amounts by the same mass, we need to consider Hooke's Law.
Hooke's Law states that the force exerted by a spring is proportional to its displacement from the equilibrium position, represented by F = -kx, where F is the force, k is the spring constant, and x is the displacement.
Since the same mass is hung from both springs, the force exerted on each spring is the same (F = mg, where m is the mass and g is gravitational acceleration). The spring that stretches the least will have a larger spring constant because, according to Hooke's Law, a larger spring constant is needed to counteract the same force with a smaller displacement. So, the spring that stretches the least has the larger spring constant.
Learn more about spring constant here:
https://brainly.com/question/14670501
#SPJ11
You are driving home from school steadily at 98 km/h for 160 km . It then begins to rain and you slow to 63 km/h instantly. You arrive home after driving 4.5 hours.a. How far is your hometown from school?b. What was your average speed?
a) The distance between school and home is 254.5 km.
b) The average speed for the entire trip is 56.6 km/h.
To answer this question, we need to use the formula: Distance = Speed x Time.
a. We know that the distance driven at a steady speed of 98 km/h is 160 km. We also know that the total time spent driving is 4.5 hours.
To find the distance between school and home, we can subtract the distance driven at 98 km/h from the total distance driven.
Distance driven at 63 km/h = (4.5 hours - time driven at 98 km/h) x 63 km/h
Distance driven at 63 km/h = 1.5 hours x 63 km/h
Distance driven at 63 km/h = 94.5 km
Total distance driven = Distance driven at 98 km/h + Distance driven at 63 km/h
Total distance driven = 160 km + 94.5 km
Total distance driven = 254.5 km
b. To find the average speed, we can use the formula: Average speed = Total distance / Total time
Average speed = 254.5 km / 4.5 hours
Average speed = 56.6 km/h (rounded to one decimal place)
To learn more about speed click on,
https://brainly.com/question/15067993
#SPJ4
You and your dog go for a walk to a nearby park. On the way, your dog takes many short side trips to chase squirrels, examine fire hydrants, and so on. When you arrive at the park, do you and your dog have the same displacement? Have you traveled the same distance?(Ch.2)
When you and your dog arrive at the park, you both have the same displacement, as displacement is the overall change in position from the starting point to the final point. However, you have not traveled the same distance. Your dog's side trips increased the total distance it traveled compared to your straighter path to the park.
Displacement is a vector quantity that represents the change in position of an object from its initial to final location, taking into account the direction of motion. The displacement of an object is the straight-line distance between its initial and final positions, measured in a specific direction. Therefore, if you and your dog started and ended your walk at the same location, the displacement will be same. On the other hand, distance is a scalar quantity that represents the total amount of ground covered by an object, without regard to the direction of motion. The distance traveled by an object is the sum of the magnitudes of the displacements along its path. Therefore, if you and your dog followed the same path to the park, you would have traveled less distance and your dog would have covered a greater distance than you.
Learn more about displacement here:
https://brainly.com/question/30087445
#SPJ11
The following statements that correctly describe the modulus of elasticity, E:
The modulus of elasticity, E, is a measure of a material's stiffness and ability to resist deformation when a force is applied. It is defined as the ratio of stress to strain within the elastic range of the material. In other words, it describes how much a material will stretch or compress under a given force.
The modulus of elasticity is important because it allows engineers to predict how materials will behave under different conditions, such as temperature changes, loading conditions, and other factors. It also helps to determine the maximum load a material can withstand before it starts to deform or break.
In detail, the modulus of elasticity is a fundamental property of a material that describes its ability to resist deformation when subjected to external forces. It is calculated by measuring the stress and strain of the material and using the equation E = σ/ε, where σ is stress and ε is strain.
The modulus of elasticity is important in many areas of engineering, such as structural design, materials science, and mechanics. It helps to ensure that structures and materials are designed and tested to withstand the loads and stresses they will be subjected to, and it provides a basis for comparing different materials and choosing the best one for a particular application.
In summary, the modulus of elasticity, E, is a material property that describes its stiffness and resistance to deformation. It is correctly determined using Hooke's Law and is crucial for predicting the mechanical behavior of materials when subjected to stress.
Learn more about Hooke's Law here:
brainly.com/question/29126957
#SPJ11
equation for kinetic energy. what is the SI unit for kinetic energy? What will happen if the speed doubles?
The equation for kinetic energy is 1/2 mv^2, where m is the mass of the object and v is its speed.
The SI unit for kinetic energy is Joules (J). If the speed doubles, the kinetic energy will quadruple because the kinetic energy is proportional to the square of the speed.Kinetic energy is a scalar quantity, meaning it has magnitude but no direction. It is typically measured in joules (J). Kinetic energy is directly proportional to the mass of the object and to the square of its velocity: increasing either of these will increase the kinetic energy. It is also proportional to the square of the frequency of a wave.
learn more about kinetic energy Refer: https://brainly.com/question/999862
#SPJ11
A brass cube, 10 cm on a side, is raised in temperature by 200°C. The coefficient of volume expansion of brass is 57 ´ 10-6/C°. By what percentage is any one of the 10-cm edges increased in length?
We can use the formula for volumetric thermal expansion:
ΔV = V₀αΔT
where ΔV is the change in volume, V₀ is the initial volume, α is the coefficient of volumetric thermal expansion, and ΔT is the change in temperature.
Since the cube has equal sides, we can find the change in length of one edge by dividing the change in volume by the initial cross-sectional area of the cube:
ΔL = ΔV/A₀
where ΔL is the change in length, and A₀ is the initial cross-sectional area.
The initial volume of the cube is:
V₀ = (10 cm)^3 = 1000 cm³
The initial cross-sectional area is:
A₀ = (10 cm)^2 = 100 cm²
The change in volume is:
ΔV = V₀αΔT = (1000 cm³)(57 × 10^-6 /°C)(200°C) = 114 cm³
The change in length of one edge is:
ΔL = ΔV/A₀ = (114 cm³)/(100 cm²) = 1.14 cm
The percentage increase in length is:
(ΔL/10 cm) × 100% = (1.14 cm/10 cm) × 100% = 11.4%
Therefore, any one of the 10-cm edges of the brass cube is increased in length by approximately 11.4%.
To know more about thermal expansion :
https://brainly.com/question/31608640
#SPJ11
Describe the perception of a pair of sinusoidal tones at 500 and 528 Hz sounded simultaneously.
For the perception of a pair of sinusoidal tones at 500 and 528 Hz sounded simultaneous, we can analyze the characteristics of the sinusoidal waves and how they interact with each other when perceived by our auditory system.
A sinusoidal tone is a type of continuous waveform that has a smooth, repetitive oscillation. When two sinusoidal tones with frequencies of 500 Hz and 528 Hz are sounded simultaneously, they will interfere with each other to create a phenomenon known as beat frequency.
The beat frequency is the difference between the two frequencies, which in this case is 528 Hz - 500 Hz = 28 Hz. This beat frequency can be perceived as a rhythmic fluctuation in the loudness of the combined sound. This occurs because the two sinusoidal waves periodically align and cancel each other out, resulting in an increase or decrease in amplitude.
In summary, when a pair of sinusoidal tones at 500 and 528 Hz are sounded simultaneously, the perception of these tones includes the experience of a beat frequency of 28 Hz, which manifests as a rhythmic fluctuation in loudness due to the interference of the two sinusoidal waves.
for more information on sinusoidal tones : https://brainly.com/question/24336803
#SPJ11
Strategy for Solving for Ideal Gas with Coefficient Analysis
The secret to solving for an ideal gas with coefficient analysis is to carefully analyse the problem and utilise a content-loaded technique to choose the best equation and variables to use. With some practise, this strategy can be a potent tool for addressing a variety of gas-related issues.
To solve for an ideal gas using coefficient analysis, it is important to have a well-planned content loaded strategy in place. This strategy should involve identifying the relevant equations and variables, as well as any known values or assumptions.
One useful approach to coefficient analysis is to use the ideal gas law, which relates the pressure, volume, temperature, and number of moles of an ideal gas:
PV = nRT
Here, P is the pressure, V is the volume, n is the number of moles, R is the gas constant, and T is the temperature. To solve for a specific variable, the equation can be rearranged using coefficient analysis. For example, to solve for volume:
V = nRT/P
In this case, the coefficients of n, R, and T are multiplied together and divided by the coefficient of P.
Overall, the key to successfully solving for an ideal gas with coefficient analysis is to carefully analyze the problem and use a content loaded strategy to identify the most appropriate equation and variables to use. With practice, this approach can be a powerful tool for solving a wide range of gas-related problems.
To know more about ideal gas click here:
https://brainly.com/question/20348074
#SPJ11
T/F If a body starts with zero velocity and ends with zero velocity, then the total change in momentum is zero.
True, if a body starts with zero velocity and ends with zero velocity, then the total change in momentum is zero.
1. Momentum is the product of an object's mass (m) and its velocity (v). It can be represented by the equation: momentum = m * v.
2. If an object starts with zero velocity (v_initial = 0), its initial momentum will be: momentum_initial = m * 0 = 0.
3. Similarly, if an object ends with zero velocity (v_final = 0), its final momentum will be: momentum_final = m * 0 = 0.
4. Change in momentum is the difference between final momentum and initial momentum: Δmomentum = momentum_final - momentum_initial.
5. Since both initial and final momenta are zero, the total change in momentum is: Δmomentum = 0 - 0 = 0.
Therefore, it is true that if a body starts with zero velocity and ends with zero velocity, the total change in momentum is zero.
To know more about the total change in momentum:
https://brainly.com/question/30487676
#SPJ11
A 3.1 kg object moving at 5.9 m/s in the positive direction of an x axis has a one-dimensional elastic collision with an object of mass M, initially at rest. After the collision the object of mass M has a velocity of 3.9 m/s in the positive direction of the x axis. What is mass M?
The mass of the second object is 6.2 kg.
The initial momentum of the system is:
[tex]p1 = m1 * v1 = (3.1 kg) * (5.9 m/s) = 18.29 kg m/s[/tex]
The final momentum of the system is:
[tex]p2 = m1 * v1' + m2 * v2'[/tex]
Since momentum is conserved, we can set p1 = p2:
[tex]m1 * v1 = m1 * v1' + m2 * v2'[/tex]
We can solve for v1' by isolating it on one side of the equation:
[tex]v1' = (m1 * v1 - m2 * v2') / m1[/tex]
Now we can use the conservation of kinetic energy to solve for m2. The initial kinetic energy of the system is:
[tex]KE1 = (1/2) * m1 * v1^2[/tex]
The final kinetic energy of the system is:
[tex]KE2 = (1/2) * m1 * v1'^2 + (1/2) * m2 * v2'^2[/tex]
Since the collision is elastic, the kinetic energy is conserved, so KE1 = KE2:
[tex](1/2) * m1 * v1^2 = (1/2) * m1 * v1'^2 + (1/2) * m2 * v2'^2[/tex]
Substituting in the expression for v1' that we found earlier, we get:
[tex](1/2) * m1 * v1^2 = (1/2) * m1 * [(m1 * v1 - m2 * v2') / m1]^2 + (1/2) * m2 * v2'^2[/tex]
Simplifying, we get:
[tex]m2 = (m1 * (v1 - v2')) / (v2' - v1)[/tex]
Plugging in the values we know, we get:
[tex]m2 = (3.1 kg * (5.9 m/s - 3.9 m/s)) / (3.9 m/s - 5.9 m/s) = 6.2 kg[/tex]
To know more about initial momentum, here
brainly.com/question/12450698
#SPJ4
what rms voltage is required to produce an rms current of 2.1 a in a 66 mh inductor at a frequency of 25 hz ?
An rms voltage of 21.79 V is required.
How to find the rms voltage?We can use the formula for the rms voltage in an AC circuit containing an inductor:
V = XL × I
where XL is the inductive reactance, I is the rms current, and V is the rms voltage.
The inductive reactance is given by the formula:
XL = 2πfL
where f is the frequency of the AC current and L is the inductance of the inductor.
Substituting the given values, we get:
XL = 2π × 25 Hz × 66 mH = 10.39 Ω
Now, we can use the formula for the rms voltage:
V = XL × I = 10.39 Ω × 2.1 A = 21.79 V
Therefore, an rms voltage of 21.79 V is required to produce an rms current of 2.1 A in a 66 mH inductor at a frequency of 25 Hz.
Learn more about rms voltage
brainly.com/question/14160294
#SPJ11
If vertically polarized light encounters a perfect polarizer and no light is transmitted, what can you conclude?
If vertically polarized light encounters a perfect polarizer and no light is transmitted, you can conclude that the polarizer is oriented horizontally or at a 90-degree angle to the incoming vertically polarized light.
This means that the polarizer is blocking the vertically polarized light from passing through, resulting in no transmitted light.
When compared to other contrast-enhancing techniques like darkfield and brightfield illumination, differential interference contrast, phase contrast, Hoffman modulation contrast, and fluorescence, polarised light produces images of higher quality.
Humans can also sense the polarisation of light, though most of us are ignorant of this ability.
Whether in the air, on Earth's surface, or under the ocean, polarised light is prevalent in natural settings.
for more information on polarized light : https://brainly.com/question/29217577
#SPJ11
(Honors) A 10.0 g bullet moves at a constant speed of 500.0 m/s and collides with a 1.50 kg wooden block initially at rest. The surface of the table is frictionless and 70.0 cm above the floor level. After the collision the bullet becomes embedded
into the block. The bullet-block system slides off the top of the table and strikes the floor. Find how far the blocks lands from the edge of the table?
The block lands 0.860 m from the edge of the table if a 10.0 g bullet moves at a constant speed of 500.0 m/s and collides with a 1.50 kg wooden block initially at rest and the surface of the table is frictionless and 70.0 cm above the floor level.
To find the distance that the block lands from the edge of the table, we need to use the conservation of energy principle.
First, we need to find the initial kinetic energy of the bullet:
K1 = (1/2) * m1 * v1^2
K1 = (1/2) * 0.01 kg * (500.0 m/s)^2
K1 = 1250 J
Next, we need to find the final kinetic energy of the bullet-block system just before hitting the ground. At this point, all of the initial kinetic energy will be converted into potential energy and final kinetic energy:
K2 = (1/2) * (m1 + m2) * v2^2
K2 = (1/2) * 1.51 kg * v2^2
We can use the conservation of energy principle to equate the initial kinetic energy to the final kinetic energy plus the potential energy:
K1 = K2 + U
1250 J = (1/2) * 1.51 kg * v2^2 + 1.51 kg * 9.81 m/s^2 * 0.7 m
Solving for v2, we get:
v2 = 79.86 m/s
Finally, we can use the horizontal component of the final velocity to find the distance that the block lands from the edge of the table:
d = (1/2) * t * v2_x
d = (1/2) * t * v2 * cos(45)
d = (1/2) * (2 * 0.7 m / 9.81 m/s^2) * 79.86 m/s * cos(45)
d = 0.860 m
For more such questions on frictionless:
https://brainly.com/question/26515803
#SPJ11
a worker pushes a crate with a force of 46 n over a 5.0-m horizontal surface. if a frictional force of 9 n acts on the cart in a direction opposite to that of the worker, what is the net work done on the cart?
The net work done on the cart is 185 J.
To calculate the net work done on the cart, we need to first calculate the
work done by the worker and the work done by friction.
The work done by the worker is given by the formula:
W1 = F1 × d × cos(theta)
where F1 is the force applied by the worker, d is the distance over which
the force is applied, and theta is the angle between the force and the
displacement. In this case, the force and displacement are in the same
direction, so theta = 0, and we have:
W1 = F1 × d = 46 N × 5.0 m = 230 J
The work done by friction is given by the formula:
W2 = F2 × d × cos(theta)
where F2 is the force of friction, d is the distance over which the force is
applied, and theta is the angle between the force and the displacement.
In this case, the force of friction is in the opposite direction to the
displacement, so theta = 180 degrees, and we have:
W2 = F2 × d × cos(180 degrees) = -9 N × 5.0 m × cos(180 degrees) = -45 J
Note that the negative sign indicates that the work done by friction is in
the opposite direction to the displacement.
The net work done on the cart is the sum of the work done by the
worker and the work done by friction:
Wnet = W1 + W2 = 230 J - 45 J = 185 J
for such more question on friction
https://brainly.com/question/31226
#SPJ11
If you calculated 108 ± 2 Ohms and the manufacturer says it is 100 Ohms with a 5% tolerance, do your data support the manufacturer's claims?
Yes, your data supports the manufacturer's claims. The manufacturer states the resistor has a value of 100 Ohms with a 5% tolerance. This means the actual resistance can vary between 95 Ohms (100 - 5) and 105 Ohms (100 + 5).
If the temperature and other physical parameters of the wire, such as stresses and strains, stay unchanged, the current flowing through the wire is precisely proportional to the potential difference applied across its ends.
In an electrical circuit with just passive components, the relationship between voltage, resistance, and current is described by Ohm's law as follows:
V=RI
where
V is the voltage that the battery provides.
R is the circuit's resistance.
Electrified heaters. Around the world, electric heaters are a typical wintertime device.
Irons and kettles with electricity. There are numerous resistors within the electric kettle and irons.
We can see from the equation that the voltage, V, and the circuit's current, I, are directly inversely proportional.
Your calculated value of 108 ± 2 Ohms falls within this range, as the lower limit is 106 Ohms (108 - 2) and the upper limit is 110 Ohms (108 + 2).
Learn more about Ohm's law here
https://brainly.com/question/14796314
#SPJ11
What was the Trade Mart? How had it seemed to change? messenger in chapter 6
The Trade Mart was a large exhibition hall in Dallas, Texas, originally built in 1936 and became significant after hosting the International Trade Mart luncheon on November 22, 1963, attended by President John F. Kennedy before his assassination.
What is the Trade Mart in Dallas, and why is it significant in relation to the assassination of President John F. Kennedy?
The Trade Mart was a large exhibition hall located in Dallas, Texas, USA. It was originally built in 1936 as part of the Texas Centennial Exposition and was designed to showcase Texas industry and agriculture. Over the years, the Trade Mart became a popular venue for trade shows, conventions, and other events.
One of the most significant events to take place at the Trade Mart was the International Trade Mart luncheon on November 22, 1963. This event was attended by President John F. Kennedy, who was assassinated later that day while riding in a motorcade through Dealey Plaza in Dallas.
After the assassination, the Trade Mart became a site of controversy and speculation. Some conspiracy theorists suggested that the Trade Mart was part of a larger conspiracy to assassinate Kennedy, while others believed that evidence related to the assassination was hidden there. However, there is no evidence to support these claims.
In the decades since the assassination, the Trade Mart has continued to serve as a venue for events and has undergone several renovations and updates. Today, it remains an important part of Dallas's cultural and commercial landscape.
To learn more about agriculture, visit: https://brainly.com/question/30351481
#SPJ1
A rigid two-blade wind turbine that is experiencing zero net torque
Entry field with correct answer
is motionless and may be horizontal or tilted.
has a constant angular velocity, which may be zero.
is motionless and horizontal.
has an angular velocity that is gradually decreasing toward zero.
A rigid two-blade wind turbine that is experiencing zero net torque means that the torque produced by the blades is equal to the torque acting on the turbine. In this scenario, the angular velocity of the turbine remains constant, which may be zero. This is because the turbine is not being affected by any external forces and is in a state of equilibrium.
However, if the turbine is left to spin on its own, its angular velocity will gradually decrease towards zero.
for such more questions on angular velocity
https://brainly.com/question/6860269
#SPJ11
If a magnet is pushed toward a solenoid it creates a voltage If it is pushed faster the voltage will ___
Reverse direction
be the same
be less
be greater
If a magnet is pushed faster toward a solenoid, the voltage induced in the solenoid will be greater.
What happens when magnet is pushed faster towards solenoid?If a magnet is pushed faster toward a solenoid, the voltage induced in the solenoid will be greater. This is due to Faraday's law of electromagnetic induction, which states that the magnitude of the voltage induced in a conductor is proportional to the rate at which the magnetic field lines passing through the conductor change.
When the magnet is pushed faster, the rate of change of the magnetic field lines passing through the solenoid increases, which in turn increases the induced voltage. Therefore, the faster the magnet is pushed, the greater the voltage induced in the solenoid.
To know more about solenoid, refer
https://brainly.com/question/1873362
#SPJ1
how is focal point and center of curvature related for a spherical mirror?
The focal point and center of curvature of a spherical mirror are related in that they both lie on the mirror's principal axis.
The center of curvature is the center of the sphere from which the mirror was cut. The focal point is the point on the principal axis at which parallel light rays incident on the mirror converge or appear to diverge from after reflection. For a concave mirror, the center of curvature is located in front of the mirror, while the focal point is located between the center of curvature and the mirror. For a convex mirror, the center of curvature is located behind the mirror, while the focal point is located behind the mirror as well.
The relationship between the focal point and center of curvature is important in understanding the behavior of light rays as they interact with spherical mirrors. It allows for the calculation of the mirror's focal length, which is a measure of the mirror's ability to converge or diverge light.
You can learn more about spherical mirror at
https://brainly.com/question/950787
#SPJ11
What is meant by conservation of charge?
a) The amount of charge in every nucleus is the same.
b) Net charge cannot be created or destroyed.
c) All electrons have the same electric charge.
d) Whenever an electron is created, an equal and oppositely charged proton is also created.
What is meant by conservation of charge?
The correct answer is:
b) Net charge cannot be created or destroyed.
The conservation of charge principle states that the total charge within an isolated system remains constant over time. This means that in any physical or chemical process, the total amount of positive charge must be equal to the total amount of negative charge. The charge is the property of matter because of which the matter experiences the force of attraction or repulsion in an electric field. The coulomb is the unit of electric charges, whereas the current is measured in the amperes.
In other words, charges can be transferred between objects, but they cannot be created or destroyed. This principle is a fundamental law of physics and is applicable to both electric and magnetic interactions.
To know more about conservation of charge:
https://brainly.com/question/10073599
#SPJ11
