The minimum number of branch circuits is determined from the total computed load and the size (or rating) of the circuits used.
What is circuit?It should be noted that circuit means a complete circular path that electricity flows through.
In this case, the minimum number of branch circuits is determined from the total computed load and the size (or rating) of the circuits used.
Learn more about circuit on:
brainly.com/question/2969220
#SPJ12
Problem 2. 2 .The particle P moves along the curved slot, a portion of which is shown. Its distance in meters measured along the slot is given by s = t^2/ where t is in seconds. The particle is at A when t = 2.00s and at B when t = 2.20s. Determine the magnitude a_avg of the average acceleration of P between A and B. Also express the acceleration as a vector a_avg using unit vectors i and j.
Magnitude of average acceleration [tex]a_{avg}[/tex]=2.75 units
Average acceleration [tex]a_{avg}=[/tex] [tex]2.265 i- 1.58j[/tex]
We're given that [tex]s=\frac{t^2}{4}[/tex]
And partice is at A at t=2 s and at B at t= 2.2s
Instantaneous velocity [tex]\frac{ds}{dt} =\frac{t}{2}[/tex]
Velocity at A ([tex]V_{a}[/tex]) at 2s = [tex]\frac{t}{2}[/tex] or [tex]\frac{t}{2}Cos \frac{\pi}{3} i+ \frac{t}{2}Sin \frac{\pi}{3}j=\frac{i+\sqrt{3} j}{2}[/tex]
Velocity at B ([tex]V_{b}[/tex]) at 2.2s =[tex]\frac{t}{2}[/tex] or [tex]\frac{t}{2}Cos \frac{\pi}{6} i+ \frac{t}{2}Sin \frac{\pi}{6}j=\frac{\sqrt{3}i+j }{2}[/tex]
Average acceleration = [tex]\frac{V_{b}-V{a}}{t}[/tex] =[tex]2.265 i- 1.58j[/tex]
magnitude = [tex]\sqrt{(2.265)^2- (1.58)^2}[/tex] = [tex]2.75[/tex]
Learn more about Acceleration here:
https://brainly.com/question/460763
#SPJ10
Role of energy consumption in formulating energy policies.
The Role of energy consumption in formulating energy policies are:
It is the regulatory framework on which global attractiveness is built.It helps widen access to electricity.It helps improve clean cooking fuels.It helps in elimination of deadly air pollution.What is the importance of energy policy?Energy policy is known to be a vital factor in economic development as it is known to be the total regulatory framework that helps to know the boast in global attractiveness and others.
Note that he Role of energy consumption in formulating energy policies are:
It is the regulatory framework on which global attractiveness is built.It helps widen access to electricity.It helps improve clean cooking fuels.It helps in elimination of deadly air pollution.Learn more about Energy policy from
https://brainly.com/question/10732684
#SPJ1
An open tank contain oil of specific gravity 0.75 on top of
water. If the depth of oil is 2m and the depth of water is 3m.
calculate the gauge and absolute pressures at the bottom of the
tank when the atmospheric pressure is 1bar
Let's not take into account atmospheric pressure.
Pressure P = Pressure of oil column + Pressure of water column
= h1 . d1.g + h2.d2. g
=( 0.5 x 800 x 9.8) + ( 1x 1000x 9.8) = 3920+ 9800 = 13720
Hence guage pressure at bottom is
P= 13720 N/ m^2
If the content of T4: 0.ACC is copied into N7: 0 through N7:4 memory locations, this process is considered a ____. A. word-to-word transfer B. file-to-file transfer C. word-to-file transfer D. file-to-word transfer
If the content of T4: 0.ACC is copied into N7: 0 through N7:4 memory locations, this process is considered a "word-to-word transfer" (Option A)
What is T4:0?
In programming, T4:0 is a time base. Whenever it is set to 1.0, it converts to the timer that counts in seconds.
It is key to note that when enumerated as T4:0 ACC, it is ascribed as an Accumulator address.
Learn more about memory locations at:
https://brainly.com/question/13104134
#SPJ1
The system dependent (passive) recovery process; A) never needs the use of a pump or heat to recover refrigerant. B) must use a pressure relief device to protect the technician and equipment. C) recovers refrigerant in a non-pressurized container. D) can only be performed on a system with an operating compressor.
Answer:
C) recovers refrigerant in a non-pressurized container
The system dependent (passive) recovery process recovers refrigerant in a non-pressurized container. The correct option is C.
A way of recovering refrigerant from a system without using a pump or heat is known as a system-dependent (passive) recovery process.
Instead, it relies on the system's normal pressure and temperature variations to speed up the recovery process.
A non-pressurized container is commonly connected to the system using this technique, and the refrigerant is then passively allowed to flow inside the container.
The system-dependent recovery procedure, according to Option C, recovers refrigerant in a non-pressurized container.
It entails that the refrigerant is gathered in a container without the need of a pump or additional pressure.
Thus, the correct option is C.
For more details regarding refrigerant, visit:
https://brainly.com/question/13002119
#SPJ6
What are the minimum and maximum required footing projections for a concrete footing having a thickness of 8 inches
The minimum and maximum required footing projections for a concrete footing having a thickness of 8 inches will be 4 inches and 8 inches.
What is projection?It should be noted that footing projections are important for construction purposes
In this case, the minimum and maximum required footing projections for a concrete footing having a thickness of 8 inches will be 4 inches and 8 inches.
Learn more about projection on:
brainly.com/question/3703881
#SPJ12
The toggle (t) flip-flop has one input, clk, and one output, q. on each rising edge of clk, q toggles to the complement of its previous value. draw a schematic for a t flip-flop using a d flip-flop and an inverter.
Answer:
See attached
Explanation:
The next state of a toggle flip-flop is the inverse of the present state. This behavior can be produced using a D flip-flop that has its input connected to the inverse of its output.
__
A schematic is attached.
what is automechanic
Answer:
An auto mechanic is a mechanic who services automobiles, sometimes specializing in one or more automobile brands or sometimes working with any brand. In repairing cars, their main role is to diagnose the problem accurately and quickly.
What is software certification? Discuss its importance in the changing scenario of software industry.
The software industry is evolving, and software certification is crucial. Software certification is a digitally signed certificate that verifies the identification of an individual or company.
What is software certification?A certificate, sometimes known as a digital certificate, is a special document that has been digitally signed and authenticates the identity of a person or business.
Its validity may be checked using public-key cryptography to make sure that the program or website you are accessing is reliable.
Software developers must demonstrate that their program executes the XBRL conformance suites successfully in order to be certified.
They must also supply extra test cases so that XBRL employees can test the program further. The validity of certification is one year, renewable yearly.
Hence the software industry is evolving, and software certification is crucial.
To learn more about the software certification refer;
https://brainly.com/question/11299456
#SPJ1
1.Which thematic group uses technology to direct the behavior of dynamical systems, ensuring that they behave in a predictable manner?
2.Which thematic group creates circuits with miniature, packaged components that directs and control electricity?
a.Communication Systems
b.Control Systems
c.Computer Systems
d.Energy Systems
e.Electronic Systems
Control systems govern the behavior of dynamic systems, while electronic systems are the ones that package the tiny components needed to conduct electricity. Thus, option E is correct.
What exactly are thematic groups?Thematic groups are made up of individuals who focus on the same theme or idea. Thematic teams working on various initiatives and concepts are made up of individuals with experience in various systems.
The function of the control system has been to regulate dynamic systems in order to bring about the desired result.The function of the electronic system thematic group is to package electronic miniatures in systems that play the job of directing electricity. Thus, option E is correct.Learn more about thematic group, here:
https://brainly.com/question/32731
#SPJ1
When adding two 8 bit binary numbers, which of the following statements is true?
Answer:
The result might require 9 bits to store
Describe four general methods used for securing an adaptor fitting when attaching hydraulic conductors to fittings and major system components.
The general methods used for securing an adaptor fitting when attaching hydraulic conductors to fittings and major system components are straight, pipe, flange, and flared.
What is a conductor?It should be noted that a conductor simply means a material that allows electricity to flow through it.
In this case, the general methods used for securing an adaptor fitting when attaching hydraulic conductors to fittings and major system components are straight, pipe, flange, and flared
Learn more about conductor on:
brainly.com/question/11845176
#SPJ12
6. During some actual expansion and compression processes in piston–cylinder devices, the gases have been
observed to satisfy the relationship PVn = C, where n and C are constants. Calculate the work done when a
gas expands from 350 kPa and 0.05 m3 to a final volume of 0.25 m3
for the case of n = 1 and 1.5.
During some actual expansion and compression processes in piston-cylinder devices, the gases have been are the P1= P2.
What is the pressure?Pressure is something that has the pressure that is physical and that causes the pressure is piston-cylinder devices.
During a few real enlargements and compression procedures in piston-cylinder devices, the gases were located to meet the connection PV n = C, wherein n and C are constants.
Read more about the pressure :
https://brainly.com/question/25736513
#SPJ1
A ____ is either in the pressure reducer or in the downstream side of the system to ensure that the control air pressure does not exceed about 30 psig. Group of answer choices
Answer:
A relief valve is either in the pressure reducer or in the downstream side of the system to ensure that the control air pressure does not exceed about 30 psig.
an incorrect way of handling disposable gloves includes
The incorrect way of handling disposable gloves are as follows;
Blow into themHold them by the fingersRoll them onto the handsWhat are disposable gloves?Disposable gloves are gloves that you use one time and then throw away.
They are usually transparent and made of nitrile, latex, or vinyl.
They are usually tough to withstand liquids and chemicals.
Therefore, the incorrect way of handling them includes the following;
Blow into themHold them by the fingersRoll them onto the handslearn more on disposable gloves here: https://brainly.com/question/24012826
#SPJ11
Proper, smooth shifting is important because if you shift before your vehicle is ready
Proper, smooth shifting is important because shifting before your vehicle is ready will cause it to je-rk forward and your drive wheels may lock.
How to properly shift your gears?A proper, smooth shifting of the gears of an automobile vehicle is very important because shifting them before the vehicle is ready would cause the following:
Jer-king forward. Lock of the drive wheels.Loss of control of the vehicle.As a good driver, proper, smooth shifting is important because shifting before your vehicle is ready will cause it to je-rk forward and your drive wheels may lock.
Read more on good drivers here: https://brainly.com/question/1071840
#SPJ1
T/f: single-strand (or solid) aluminum branch circuit wiring observed by a home inspector should always be fully evaluated by a licensed electrical contractor.
The statement "Single-strand (or solid) aluminum branch circuit wiring observed by a home inspector should always be fully evaluated by a licensed electrical contractor" is definitely true.
What is an Electrical Circuit?An electrical circuit may be defined as a complete path through which an electric current continuously flows when the switch is in on state. It is an enclosed system of current flowing.
The quality of each and every wire does not matter if it is made up of aluminum or copper should be monitored by a high level of engineers and then a license has to be issued to that wiring company on the behalf of an electrical contractor.
Therefore, it is well described above.
To learn more about Electrical contractors, refer to the link:
https://brainly.com/question/24014509
#SPJ1
A bakery wants to determine how many trays of doughnuts it should prepare each day. Demand is normal with a mean of 15 trays and standard deviation of 5 tray. If the owner wants a service level a at least 95%?
The number of trays that should be prepared if the owner wants a service level of at least 95% is; 7 trays
How to utilize z-score statistics?We are given;
Mean; μ = 15
Standard Deviation; σ = 5
We are told that the distribution of demand score is a bell shaped distribution that is a normal distribution.
Formula for z-score is;
z = (x' - μ)/σ
We want to find the value of x such that the probability is 0.95;
P(X > x) = P(z > (x - 15)/5) = 0.95
⇒ 1 - P(z ≤ (x - 15)/5) = 0.95
Thus;
P(z ≤ (x - 15)/5) = 1 - 0.95
P(z ≤ (x - 15)/5) = 0.05
The value of z from the z-table of 0.05 is -1.645
Thus;
(x - 15)/5 = -1.645
x ≈ 7
Complete Question is;
A bakery wants to determine how many trays of doughnuts it should prepare each day. Demand is normal with a mean of 15 trays and standard deviation of 5 trays. If the owner wants a service level of at least 95%, how many trays should he prepare (rounded to the nearest whole tray)? Assume doughnuts have no salvage value after the day is complete. 6 5 4 7 unable to determine with the above information.
Read more about Z-score at; https://brainly.com/question/25638875
#SPJ1
ensures that enough pressure is placed on the bearing to keep the shaft from moving around, but not so much that the bearing will run hot and begin to fail. Group of answer choices End play Preload Both A and B Neither A nor B
Preload ensures that enough pressure is placed on the bearing, so as to keep the shaft from moving around while preventing the bearing from running hot.
What is preload?Preload can be defined as the load (amount of force) that is generated from an axial interference within a bearing, which causes an elastic deformation between the rolling elements and raceway.
In Engineering, preload is a technique which ensures that enough pressure is placed on the bearing, so as to keep the shaft from moving around while preventing the bearing from running hot and failing.
Read more on preload here: https://brainly.com/question/16342676
#SPJ12
a set of several wires wrapped in tape or enclosed in a plastic sheath is referred to as
Answer:
A. Wire Harness
Please show NEC article 310.10(H)
Conductors in Parallel is covered in 310.10(H). Often when working with higher ampacities, we find it to be cumbersome and expensive to keep increasing the size of the wire and conduit. The solution is often to use multiple runs that are connected to a common location on each end. Notice in the 2011 edition of the code that much of this section is highlighted gray, indicating new or revised text. The change here was that the previous code stated that you were permitted to parallel conductors 1/0 AWG and larger; however, it didn’t specifically prohibit you from paralleling smaller conductors, which was the intent and the way it was enforced in all my years of enforcement. However, that’s not what the actual language said, and ambiguous language cancause enforcement issues; therefore, in the 2011 code it was made clear that you are only allowed to parallel conductors 1/0 AWG and larger.
a low velocity fastening system that is used to drive steel pins or threaded studs into a masonry and steel is a
A low velocity fastening system that is used to drive steel pins or threaded studs into a masonry and steel is a powder-actuated tool.
What is a fastening system?It should be noted that a fastening system is important to fixing rails to railroad ties.
In this case, a low velocity fastening system that is used to drive steel pins or threaded studs into a masonry and steel is a powder-actuated tool.
Learn more about fasteners on:
brainly.com/question/16350719
#SPJ12
(a)Identify the relevant population for the below foci, and suggest the appropriate sampling
design to investigate the issues, explaining why they aare appropriate. Wherever necessary
identify the sampling frame as well.
A public relations research department wants to investigate the initial reactions of heavy soft-
drink users to a new all-natural soft drink
The relevant population for the below foci example is a small population and:
When a firm wants to investigate the first response of heavy fruit drink uses to a new all natural fruit drink and the best sampling to use random sampling.What is Simple random sampling?This is known to be a kind of probability sampling where the researcher randomly takes a subset of participants from a given population.
Note that the member of the population has an equal chance of being selected and as such, in the case above, The relevant population for the below foci example is small population and:
A firm wants to investigate the first response of heavy fruit drink uses to a new all natural fruit drink and the best sampling to use random sampling.Learn more about population from
https://brainly.com/question/25630111
#SPJ1
Air is compressed from 20 psia and 70°F to 150 psia in a compressor. The compressor is operated such that the air temperature remains constant. Calculate the change in the specific volume of air as it passes through this compressor.
Answer: -8.51 ft^3/lbm
Explanation:
In this question, to find the change in volume, we will use the ideal gas law.
[tex]\begin{aligned}&n_{1}=1 \text { mole }\\&\mathrm{P}_{1}=20 \mathrm{psia}\\&\mathrm{T}_{1}=70^{\circ} \mathrm{F}\\&T_{1}=(70+460)^{0} \mathrm{R}\\&v_{1}=\frac{\left(0.3704 \frac{psia \cdot_{\text { } ft^{3}}}{l \mathrm{lbm} \cdot R}\right)(70+460)^{0} \mathrm{R}}{20 \mathrm{psi}}\\&v_{1}=9.816 \frac{\mathrm{ft}^{3}}{\mathrm{lbm}}\end{aligned}[/tex]
[tex]\begin{aligned}&\mathrm{n}_{2}=1 \text { mole } \\&\mathrm{P}_{2}=150 \mathrm{psia} \\&\mathrm{T}_{1}=\mathrm{T}_{2}=70^{0} \mathrm{~F} \\&\mathrm{~T}_{1}=\mathrm{T}_{2}=(70+460)^{0} \mathrm{R} \\&v_{2}=\frac{\left(0.3704 \frac{\text { psia} \cdot \mathrm{ft}^{3}}{\mathrm{lbm} \cdot R}\right)(70+460)^{0} \mathrm{R}}{150 \mathrm{psi}} \\&v_{2}=1.309 \frac{\mathrm{ft}{ }^{3}}{\mathrm{lbm}}\end{aligned}[/tex]
[tex]$$The change in volume is,$$\begin{aligned}&\Delta v=v_{2}-v_{1} \\&\Delta v=1.309-9.816 \\&\Delta v=-8.51 \frac{\mathrm{ft}^{3}}{\mathrm{lbm}}\end{aligned}\text{The negative sign shows that the gas was compressed during this process}[/tex]
3 To improve the acoustics in auditorium, a sound reflector with mass
of 200 kg is suspended by a chain from the ceiling. What is its
weight? What force (magnitude and direction) does the chain exert
on it? What is the tension in the chain? Assume that the mass of the
chain itself is negligible.
To improve the acoustics in auditorium, a sound reflector with mass of 200 kg is suspended by a chain from the ceiling thus thet force (magnitude and direction) does the chain exert on it =1960 N.
What is Newton's third regulation?
Ths 0.33 regulation states that for each movement (pressure) in nature there's an identical and contrary response. If item A exerts a pressure on item B, item B additionally exerts an identical and contrary pressure on item A. In different words, forces end result from interactions.
Weight of reflector = mg=200^ * 9.8=1960 NForce exerted with the aid of using chain =1960 NDirection = upwardsTension at the chain = weight of reflector=1960 NWeight of reflector =mg =100 * 9.8=980NMagniyof pressure reflector exerts on earth = 980 N(Due to movement response pair of forces, consistent with Newton's 0.33 regulation of motion.Read more about the Newton's law:
https://brainly.com/question/25545050
#SPJ1
Draw isometric projection of a pls help
Draw isometric projection Spatial axes of the item are represented as similarly willing to the drawing floor and same distances alongside the axes are drawn the same.
What is isometric projection?Definition of isometric projection an axonometric projection wherein the 3 spatial axes of the item are represented as similarly willing to the drawing floor and same distances alongside the axes are drawn same.
An isometric view of an item may be received via way of means of selecting the viewing path such that the angles among the projections of the x, y, and z axes are all of the same, or 120°. For example, with a cube, that is achieved via way of means of first searching immediately toward one face.
Read more about the data:
https://brainly.com/question/25749514
#SPJ1
In third ange projection draw the plain view, front view and end view.
Answer:
The front view, is a drawing of the block, as if you are looking directly at the front of the object. The side view, is a drawing of the block, when it has been rotated so that one of its sides is now directly in view. The plan view, is a 'birds eye' view, from above.
When starting a vehicle with an automatic transmission, be sure the gear selector is set in (P)ark or ________.
When starting a vehicle with an automatic transmission, be sure the gear selector is set in (P)ark or (D)rive.
What are automatic cars?Automatic cars are those who have automatic options for shifting of gears. We do not have to adjust the gears by ourselves.
These cars have mode of Park, if we are moving the car, to start the car we must change it from Park to drive mode.
Thus, the fill the blank is Drive.
Learn more about automatic cars
https://brainly.com/question/14646065
#SPJ1
A transformer has 300,000 windings in its primary coil and uses 12,000V AC input. (4 points) How many windings would be needed to produce at output of 110V AC
Answer:
2750
Explanation:
The number of windings and the voltage are proportional.
__
Let n represent the number of windings to produce 110 Vac. Then the proportion is ...
n/110 = 300,000/12,000
n = 110(300/12) = 2750 . . . . multiply by 110
2750 windings would be needed to produce 110 Vac at the output.
You should have at least a ___ mph speed advantage when passing another vehicle
A driver should have at least a 10 mph speed advantage when overtaking (passing) another vehicle.
What is a speed limit?A speed limit refers to the maximum amount of speed that is legally permitted or allowed in a specific area for safety. Thus, this limit must be abided and strictly adhered to by all road users such as drivers of a vehicle.
According to the highway traffic code and regulations, a driver should have at least a 10 mph speed advantage when overtaking (passing) another vehicle.
Read more on safety here: https://brainly.com/question/14751268
#SPJ12
