Use of SG to Calculate Weight (Mass) Using the SI System Must know the SG and the volume KNOW THIS Equation Grams = milliliters × SG Example Mass in grams of 2450 mL of ethanol (SG=0.810) 2450 mL × 0.810 = 1984.5 g

In the process of performing a vacuum filtration, while slowly pouring the mixture out of your Erlenmeyer flask into the Buchner funnel, you would observe the solids being separated from the liquid. The solid particles will be trapped on the filter paper or fritted glass, while the liquid (filtrate) will be drawn through the funnel by the vacuum and collected in the flask below.

To ensure that you don't lose any solids, you should:

1. Wet the filter paper or fritted glass with a small amount of solvent before adding the mixture. This will help the solids adhere better and prevent them from passing through the filter.
2. Pour the mixture slowly and carefully into the Buchner funnel to minimize splashing and prevent any solids from escaping.
3. If there are any remaining solids in the Erlenmeyer flask, rinse it with a small amount of solvent and pour this rinse into the Buchner funnel. This will help to transfer any residual solids onto the filter.
4. Once the filtration is complete, allow the vacuum to run for a few more minutes to ensure that all the liquid has passed through and the solids are adequately dried.

By following these steps, you will minimize the loss of solids during the vacuum filtration process and obtain a better separation of the solid and liquid components.

To know more about vaccum filtration:

https://brainly.com/question/31504556

#SPJ11

To find the total number of valence electrons in the molecule XeBr₂Cl₂, you'll need to consider the valence electrons of each element in the compound. The elements are Xenon (Xe), Bromine (Br), and Chlorine (Cl).

1. Xenon (Xe) has 8 valence electrons, as it is in Group 18 of the periodic table.
2. Bromine (Br) has 7 valence electrons, as it is in Group 17. Since there are two Bromine atoms in the compound (Br₂), you'll need to multiply 7 by 2, which equals 14.
3. Chlorine (Cl) also has 7 valence electrons, as it is in Group 17 as well. Since there are two Chlorine atoms in the compound (Cl₂), you'll need to multiply 7 by 2, which equals 14.

Now, add the valence electrons of all the elements in the compound:
Total valence electrons = Valence electrons of Xe + Valence electrons of Br₂ + Valence electrons of Cl₂
Total valence electrons = 8 + 14 + 14

The total number of valence electrons in the molecule XeBr₂Cl₂ is 36.

To know more about valence electrons:

https://brainly.com/question/31264554

#SPJ11

SDS will only interrupt non-covalent bonds, so if disulfide bridges are present in the protein, they will not be broken. This is because disulfide bridges are covalent bonds formed between two cysteine residues within a protein, providing stability to its structure.

SDS, or sodium dodecyl sulfate, is an anionic detergent commonly used in denaturing proteins by disrupting non-covalent bonds such as hydrogen bonds, electrostatic interactions, and hydrophobic effects.

However, SDS cannot break disulfide bridges as it does not possess the reactivity to cleave covalent bonds. To break disulfide bridges, reducing agents like beta-mercaptoethanol or dithiothreitol (DTT) are often used in conjunction with SDS to fully denature proteins for analysis.

To know more about non-covalent bonds refer here:

https://brainly.com/question/10863848#

#SPJ11

The M904 and M905 delay elements are part of the guidance system used for the Standard Missile 3 (SM-3) interceptor missile. The M904 delay element is placed between the missile's boost motor and the separating stage, while the M905 delay element is placed between the missile's separating stage and the guided missile's rocket motor.

These delay elements are inserted into the missile's payload at specific times and for specific reasons:

The pH of the solution 10.48., we need to first determine the concentration of hydroxide ions (OH-) or hydrogen ions (H+) in the solution.

Potassium acetate is a salt of a weak acid (acetic acid) and a strong base (potassium hydroxide). It will undergo hydrolysis in water to produce OH- ions:

CH3CO2- + H2O ↔ CH3COOH + OH-

We can use the equilibrium constant expression for this hydrolysis reaction to determine the concentration of OH- ions:

Kw/Ka = [OH-][CH3COOH] / [CH3CO2-]

Kw is the ion product constant of water (1.0 x 10^-14) and Ka is the acid dissociation constant of acetic acid (1.8 x 10^-5).

Since we are given the mass of potassium acetate and the volume of solution, we can use this information to calculate the molarity (M) of the solution:

M = moles of solute / volume of solution in liters

moles of solute = mass of potassium acetate / molar mass of potassium acetate

molar mass of potassium acetate = 101 g/mol (39 + 2(12) + 6(1) + 2(16))

moles of solute = 8.4 g / 98 g/mol = 0.08316 mol

volume of solution = 250 cm^3 = 0.25 L

M = 0.0857 mol / 0.25 L = 0.33 M

Now we can use the concentration of potassium acetate and the equilibrium constant expression to solve for the concentration of OH- ions:

0.343 = (1.0 x 10^-14) / (1.8 x 10^-5) x [OH-][CH3COOH] / [CH3CO2-]

Since we know that [H+] = Kw / [OH-], we can substitute in the value we found for [OH-]:

pH = -log[(1.0 x 10^-14) / (2.36 x 10^-4)] = 10.48

Therefore, the pH of the solution is approximately 10.48.

Click the below link, to learn more about pH of solution:

https://brainly.com/question/30934747

#SPJ11

In the process of reducing Benzil to hydrobenzoin, two stereocenters are produced. These stereocenters give rise to the possibility of different stereoisomers, such as (R,R)-hydrobenzoin, (S,S)-hydrobenzoin, and (R,S)- or (S,R)-hydrobenzoin (meso-hydrobenzoin), depending on the spatial arrangement of the groups around the stereocenters.

Benzil is an organic compound with the formula (C6H5CO)2. In the process of reducing benzil, we usually use a reducing agent such as sodium borohydride (NaBH4) to convert the carbonyl groups into alcohol groups, forming hydrobenzoin as the product.

The key to understanding the number of stereocenters produced lies in examining the structure of hydrobenzoin. Hydrobenzoin has the molecular formula C14H14O2 and consists of two phenyl rings connected by a central carbon chain with two hydroxyl (OH) groups. The central carbon chain consists of two carbons, each bearing a hydroxyl group.

The stereocenters in hydrobenzoin, A stereocenter is an atom at which the interchange of two groups creates a different stereoisomer. In this case, both central carbons with hydroxyl groups are stereocenters, as they each have four different groups attached to them (a phenyl group, a hydroxyl group, a hydrogen atom, and the other central carbon).

For More Such Questions on Benzil

https://brainly.com/question/9415260

#SPJ11

The point at which the pH of a buffered solution will begin to change significantly is: just before one of the components of the buffer is used up.

A buffered solution is designed to resist changes in pH when small amounts of acid or base are added. It typically contains a weak acid and its conjugate base, or a weak base and its conjugate acid.

As hydronium or hydroxide ions are added, the buffer components react to neutralize them, maintaining the pH within a certain range.

However, once one of the buffer components is nearly depleted, the buffering capacity is reduced, and the pH will begin to change significantly with the addition of more acid or base.

To know more about buffered solution refer here:

https://brainly.com/question/24262133#

#SPJ11

Xylene is often used as a solvent for Diels-Alder reactions due to its high boiling point and ability to dissolve a wide range of organic compounds.

Xylene is a common solvent used in various applications due to its favorable physical and chemical properties. Two reasons why xylene is often used as a solvent are:

Learn more about Xylene

https://brainly.com/question/27860606

#SPJ4

The correct name for the compound N2O5 is dinitrogen pentoxide. This is because N2O5 is a covalent compound composed of two nitrogen atoms and five oxygen atoms. The correct option is A).

The prefix "di" indicates that there are two nitrogen atoms present in the molecule, and the suffix "-pentoxide" indicates that there are five oxygen atoms present. Therefore, the name "dinitrogen pentoxide" accurately reflects the composition of the molecule.

It is important to note that options B, C, D, and E are all incorrect. Nitrogen oxide is a general term that can refer to any compound composed of nitrogen and oxygen. Nitrogen(V) oxide and nitrogen(III) oxide are not valid names for N2O5 because they do not accurately reflect the composition of the molecule. Nitrogen pentoxide is also not a valid name because it implies that there is only one nitrogen atom present in the molecule, when in fact there are two. Therefore, the correct name for N2O5 is dinitrogen pentoxide.

For more such questions on Compound.

https://brainly.com/question/29610670#

#SPJ11

Kidney stones form in some individuals treated with Compound 1 - [[tex]Ca^{2+}[/tex]][[tex]C_2O_4^2[/tex]] because calcium oxalate precipitates when [[tex]Ca^{2+}[/tex]][[tex]C_2O_4^{2-}[/tex]] exceeds the solubility product constant Ksp by definition. Option B is the correct answer.

Kidney stones can form when there is an excess of calcium and oxalate ions in the urine, leading to the formation of calcium oxalate crystals. Compound 1 likely increases the concentration of calcium and/or oxalate ions in the urine, leading to an increased risk of kidney stone formation. The correct answer is B, [[tex]Ca^{2+}[/tex]][[tex]C_2O_4^{2-}[/tex]] > Ksp, as this condition would result in the precipitation of calcium oxalate, which can form kidney stones.

Treatment options for kidney stones depend on the size, location, and composition of the stone, and may include medications, dietary changes, or surgical intervention.

Learn more about kidney stones at

https://brainly.com/question/29473472

#SPJ4

The question is -

Why do kidney stones form in some individuals treated with Compound 1 - [Ca^2+][C2O4^2]?

A. [Ca2+] + [C2O42–] > Ksp

B. [Ca2+][C2O42–] > Ksp

C. [Ca2+] + [C2O42–] < Ksp

D. [Ca2+][C2O42–] < Ksp

Hyperaldosteronism leads to increased release of aldosterone which leads to increased activity of the basolateral Na⁺/K⁺ pump in the principal cell. This leads to hypokalemia. The H⁺ ions then take over and take the place of K⁺ on the Na⁺/K⁺ ATPase but this causes loss of H⁺ and alkalosis.

Hyperaldosteronism is a condition where the adrenal gland produces excess aldosterone hormone. Aldosterone plays a crucial role in regulating the body's fluid and electrolyte balance, specifically by increasing sodium reabsorption in the kidney and promoting potassium and hydrogen ion excretion.

When there is excess aldosterone, it leads to increased activity of the basolateral Na⁺/K⁺ pump in the principal cell of the kidney, resulting in increased sodium reabsorption and potassium excretion. This leads to hypokalemia, which is a condition characterized by low levels of potassium in the blood.

To compensate for the hypokalemia, the H⁺ ions start to take over and replace K⁺ on the Na⁺/K⁺ ATPase, leading to increased secretion of H⁺ ions into the urine. As a result, there is a loss of H⁺ ions from the body, leading to alkalosis, a condition characterized by an increase in blood pH.

To know more about adrenal gland, refer here:
https://brainly.com/question/23487477#
#SPJ11

For an inflow rate of 75 L/s, a contaminant concentration of 0.05 mol/L, and a degradation rate constant of 0.10/s, the CSTR volume needed to achieve 98% degradation of an organic compound is about 604.8 L.

To calculate the CSTR volume required for 98% degradation of an organic compound, we can use the following formula:

V = Q / (k [tex]*[/tex] C [tex]*[/tex] ln(1/(1-X)))

where:

Plugging in the given values:

V = 75 / (0.10 [tex]*[/tex] 0.05 [tex]*[/tex] ln(1/(1-0.98)))

V = 604.8 liters

Therefore, the CSTR volume required for 98% degradation of the organic compound is approximately 604.8 liters.

Learn more about CSTR volume

brainly.com/question/13739627

#SPJ11

The presence of multiple codons for some amino acids is beneficial as it provides error protection, flexibility, and regulation in protein synthesis and gene expression.

The redundancy of multiple codons for a single amino acid is a feature called "degeneracy" in the genetic code. This redundancy helps in several ways:

1. Error protection: If there's a mutation or error in one codon, the alternate codon might still code for the same amino acid, preventing errors in protein synthesis.

2. Flexibility: Having multiple codons for one amino acid allows for variations in DNA sequences without changing the protein's function, which contributes to genetic diversity and adaptation.

3. Regulation: Different codons for the same amino acid can be translated at different rates, allowing for fine-tuning of protein synthesis and gene expression.

To know more about Amino acids:

https://brainly.com/question/3165690

#SPJ11

The plan of care for a client who takes lithium should include periodic laboratory monitoring of renal and thyroid function and the correct option is option 3.

Two major long-term risks of lithium therapy are hypothyroidism and impairment of the kidney's ability to concentrate urine

Therefore, a person receiving lithium therapy must have periodic follow-ups to assess thyroid and renal function.

Weight gain and fine tremors are common side effects associated with this medication, but the patient should continue taking the medication.

Thus the ideal selection is option 3.

Learn more about Lithium intake, here:

https://brainly.com/question/31449457

#SPJ4

The standard free energy change of the reaction is -9.95. The answer is option C

To calculate ΔG°rxn, we can use the equation ΔG°rxn = -RT ln Kp,

where R is the gas constant, T is the temperature in Kelvin, and ln is the natural logarithm. At 25°C, which is 298 K,.

We can substitute these values along with the given Kp value of 0.018 into the equation to obtain:

ΔG°rxn = - (8.314 J/mol·K) x (298 K) x ln(0.018) ≈ -9.95 kJ/mol

Therefore, the answer is option C, -9.95.

This equation calculates the standard free energy change of a reaction at a specified temperature.

The negative sign in front of the result indicates that the reaction is spontaneous in the forward direction under standard conditions.

The magnitude of ΔG°rxn indicates the degree of spontaneity of the reaction: the more negative the value, the more spontaneous the reaction.

In this case, the reaction is moderately spontaneous, but still has a significant activation energy barrier that needs to be overcome for it to occur.

To know more about  standard free energy change, refer here:
https://brainly.com/question/15876696#
#SPJ11

The reaction mechanism is different. In the case of aldehydes, the nucleophile attacks the electrophilic carbon of the carbonyl group, resulting in the formation of a new bond and the release of a leaving group, usually a proton. This results in the formation of a new carbon-nucleophile bond and the formation of an alcohol.

In the case of acyl chlorides, the reaction mechanism involves the attack of the nucleophile on the acyl chloride, resulting in the formation of a tetrahedral intermediate.

This intermediate then undergoes elimination of the chloride ion, resulting in the formation of a new carbon-nucleophile bond and the release of a chloride ion. This results in the formation of an ester.

Click the below link, to learn more about Aldehydes vs Acyl Chlorides:

https://brainly.com/question/30902678

#SPJ11

The relationship between an electron's mass (m), its speed (u), and its kinetic energy (KE) can be represented by the equation KE = (1/2)mu^2.

Therefore, the correct answer is option C. This equation demonstrates that the kinetic energy of an electron is directly proportional to both its mass and the square of its speed.

What is Kinetic energy ?

Kinetic energy is is the energy of mass in motion basically the kinetic energy of an object is the energy it has because of its motion an example of kinetic energy would be, well let’s say you have a ball and you let that ball fall the potential energy then converts into kinetic energy or the energy associated with the motion and there are five types of kinetic energy like (radiant and thermal and sound and electrical and mechanical.

To know more about electron's mass :

https://brainly.com/question/1287241

#SPJ11

The short-acting benzodiazepines are a class of drugs that act as central nervous system depressants and are commonly used to treat anxiety and sleep disorders.

Benzodiazepines work by enhancing the effects of the neurotransmitter gamma-aminobutyric acid (GABA), which helps to reduce neuronal excitability and produce sedative, anxiolytic, and anticonvulsant effects.

Short-acting benzodiazepines have a relatively rapid onset of action and a shorter duration of action than other benzodiazepines. This makes them useful for treating acute symptoms of anxiety or insomnia, but they may also be associated with a greater risk of dependence and withdrawal symptoms.

Some common short-acting benzodiazepines include midazolam, triazolam, and lorazepam. These drugs are typically used for short-term treatment of anxiety or insomnia and are generally not recommended for long-term use due to the potential for tolerance, dependence, and withdrawal.

Patients taking short-acting benzodiazepines should be closely monitored for side effects and may require a tapering regimen to safely discontinue the medication.


The correct question is:
What are the short-acting benzodiazepines?

To know more about sleep disorders, refer here:
https://brainly.com/question/30451093#
#SPJ11

The 3 methods to accomplish cis-dihydroxylation are by osmium trioxide,Woodward reaction and N-methylmorpholine.

Dihydroxylation is the process by which an alkene is converted into a vicinal diol. Although there are many routes to accomplish this oxidation, the most common and direct processes use a high-oxidation-state transition metal (typically osmium or manganese). The method uses metal  often used as a catalyst, with some other stoichiometric oxidant present. In addition, other transition metals and non-transition metal methods have been developed and used to catalyze the reaction.

Learn more about dihydroxylation,here:

https://brainly.com/question/17051072

#SPJ4

32.25 × 10^23 atoms are present in a sample of pure iron with a mass of 300 g.

To find out how many atoms are present in a sample of pure iron with a mass of 300 g, you'll need to use the atomic mass of iron and Avogadro's number (NA). Here are the steps to calculate this:

1. Convert the mass of iron to moles using the atomic mass:
  Moles of iron = (mass of iron) / (atomic mass of iron)
  Moles of iron = (300 g) / (56 g/mol)

2. Calculate the number of atoms using Avogadro's number:
  Atoms of iron = (moles of iron) × (NA)
  Atoms of iron = (300 g / 56 g/mol) × (6.02 × 10^23 atoms/mol)

  Atoms of iron = 32.25 × 10^23 atoms

Therefore, the number of atoms are 32.25 × 10^23 atoms.

To learn more about "iron", visit: https://brainly.com/question/14964747

#SPJ11

A) One possible molecular formula is C₁₂H₂₀Cl₂O₄., B)  One possible molecular formula is C₁₀H₂₀Cl₄O₄, C)  One possible molecular formula is C₁₂H₂₀Cl₄O₄, D)  One possible molecular formula is C₁₂H₂₀O₄ and  E)  One possible molecular formula is C₁₂H₂₄Cl₄O₈.

To determine a possible molecular formula for a given empirical formula, we need to determine the molecular mass of the compound by finding the molar mass of the empirical formula and multiplying it by a whole number that will give the desired molecular formula.

A) C₆H₁₀ClO₂

The molar mass of the empirical formula is:

6(12.01 g/mol) + 10(1.01 g/mol) + 16.00 g/mol + 2(15.99 g/mol) = 162.18 g/mol. A possible molecular formula with a molecular mass that is a multiple of 162.18 g/mol is C₁₂H₂₀Cl₂O₄.

B) C₅H₁₀Cl₂O₂

The molar mass of the empirical formula is:

5(12.01 g/mol) + 10(1.01 g/mol) + 2(35.45 g/mol) + 2(15.99 g/mol) = 202.12 g/mol. A possible molecular formula with a molecular mass that is a multiple of 202.12 g/mol is C₁₀H₂₀Cl₄O₄.

C) C₆H₁₀Cl₂O₂

The molar mass of the empirical formula is:

6(12.01 g/mol) + 10(1.01 g/mol) + 2(35.45 g/mol) + 2(15.99 g/mol) = 236.10 g/mol. A possible molecular formula with a molecular mass that is a multiple of 236.10 g/mol is C₁₂H₂₀Cl₄O₄.

D) C₆H₁₀O₂

The molar mass of the empirical formula is:

6(12.01 g/mol) + 10(1.01 g/mol) + 2(15.99 g/mol) = 102.16 g/mol A possible molecular formula with a molecular mass that is a multiple of 102.16 g/mol is C₁₂H₂₀O₄.

E) C₆H₁₂Cl₂O₂

The molar mass of the empirical formula is:

6(12.01 g/mol) + 12(1.01 g/mol) + 2(35.45 g/mol) + 2(15.99 g/mol) = 252.20 g/mol A possible molecular formula with a molecular mass that is a multiple of 252.20 g/mol is C₁₂H₂₄Cl₄O₄.

To know more about  molecular formula, refer here:
https://brainly.com/question/14425592#
#SPJ11

The two methods of the classifying bomb Fuzes are the detonating and the igniting.

The two methods of the classification of the bomb fuzes are the detonating and the igniting. The Detonating fuzes are the explode in the grenade body then initiate the filler. The Detonating fuzes are the used to the high explosive and the chemical type of the grenades.

The Igniting fuzes that will burn at the high temperatures to the ignite then the filler. The  Igniting fuzes are the fuzes that are used with all the burning the type of the chemical grenades and this is with the practice grenades.

To learn more about fuzes here

https://brainly.com/question/20383504

#SPJ4

The type of bonding found in the compound PCl5 is A) covalent bonding.

Phosphorus (P) and chlorine (Cl) are both nonmetals, and when nonmetals form compounds, they typically form covalent bonds by sharing electrons. In PCl5, one phosphorus atom shares electrons with five chlorine atoms, creating covalent bonds between them.

A covalent bond consists of the mutual sharing of one or more pairs of electrons between two atoms. These electrons are simultaneously attracted by the two atomic nuclei.

A covalent bond forms when the difference between the electronegativities of two atoms is too small for an electron transfer to occur to form ions.

To know more about covalent bonding refer here:

https://brainly.com/question/10777799

#SPJ11

If the safety pin comes out the while we are handling the BDU-33 practice bomb that has the  MK4 MOD 3 signal cartridge, we must notify the supervisor so that the bomb should be repair.

If the safety pin will comes out the while we are handling the BDU-33 practice bomb and been that has the MK4 MOD 3 signal cartridge, we must notify the our supervisor so that the bomb should be repair. The 2W1's aren not authorized to do the maintenance.

The  BDU-33 practice bomb will weigh in the pounds is the 25 pounds. The BDU-33 practice bomb will be provides the force that is combat air forces with the inert munition to the facilitate the aircrew weapons delivery in the training.

To learn more about bomb here

https://brainly.com/question/30288409

#SPJ4

The pH of the water would be 2. This is because HCl is a strong acid that dissociates completely in water, producing a large amount of hydrogen ions (H+), which lower the pH.

A pH of 2 is highly acidic and would be an extreme environment for most living organisms, but some extremophilic archaea are known to thrive in acidic conditions.

To determine the pH of the water, we will use the following formula:

pH = -log[tex]^{10}[/tex][H+]

Where [H+] is the concentration of hydrogen ions in the solution. In this case, the concentration of HCl is given as 0.01 M. Since HCl is a strong acid, it will dissociate completely in water, resulting in an equal concentration of H+ ions:

[H+] = 0.01 M

Now, we can use the formula to calculate the pH:

pH = -log[tex]^{10}[/tex](0.01) = 2

So, the pH of the water in the pool where the archaebacterial species lives is 2 (option c).

More on pH: https://brainly.com/question/20389094

#SPJ11

4.54 × 10²²  atoms of cesium are in 12.4 grams of cesium phosphate when the number of moles is given as 0.0754 moles.

A mole is defined as the amount of substance containing the same number of atoms, molecules, ions, etc. as the number of atoms in a sample of pure 12C weighing exactly 12 g.

Given,

Moles of Cs = 0.0754 moles

Mass of Cesium phosphate = 12.4g

1 mole of a substance has 6.023 × 10²³ atoms

Therefore, 0.0754 moles will have 6.023 × 10²³ × 0.0754

= 4.54 × 10²² atoms

Learn more about Moles, here:

https://brainly.com/question/26416088

#SPJ4

The pH of a hydroxide relaxer is typically 13 or higher which is considered a high alkaline concentration.

pH is a numerical indicator of how acidic or basic aqueous and other liquid solutions are. The phrase, which is frequently used in the fields of biology, agronomy, and chemistry, converts the hydrogen ion concentration, which typically ranges between 1 and 1014 gram-equivalents per litre, into numbers ranging from zero to fourteen. The hydrogen ion concentration in pure water, which has a pH of 7, is 107 gram-equivalents per litre, making it neutral. The pH of a hydroxide relaxer is typically 13 or higher which is considered a high alkaline concentration.

Therefore,  the pH of a hydroxide relaxer is typically 13.

To know more about pH, here:

https://brainly.com/question/27945512

#SPJ4

A client, who is a self-employed plumber, was referred to our service due to low back pain caused by tasks that involve stooping and twisting in his work. The problem is that he is at risk of Injury due to unsafe practices at work. Our approach will be preventative, focusing on preventing further injury.

To achieve this, we will conduct a series of assessments, including a client interview to understand his daily tasks and challenges, a work-site assessment to identify hazards and risks in his workplace, and a risk assessment to determine the most appropriate interventions.

Our primary intervention techniques will involve educating the client on correct body mechanics and safe moving and handling techniques within his workplace. This education will not only help him perform tasks more safely but also reduce the likelihood of future injuries. In addition to workplace education, we may also provide guidance on safe moving and handling practices at home, further supporting his overall well-being.

By focusing on preventative measures and educating the client on safe practices, we aim to reduce the risk of injury and promote a healthier, more ergonomic work environment for the self-employed plumber.

For More Such Questions on Injury

https://brainly.com/question/30587585

#SPJ11

If we had used an oxidizable metal wire instead of copper, it would have affected the final molar mass of magnesium. This is because oxidizable metals react with oxygen in the air and form oxides on their surface. This oxide layer can add to the weight of the metal wire and hence, increase the mass of the magnesium obtained.

However, when we calculate the molar mass of magnesium, we take into account the mass of the magnesium obtained and not the mass of the metal wire. Therefore, the use of an oxidizable metal wire would not affect the final molar mass of magnesium obtained.

In conclusion, while the use of an oxidizable metal wire may affect the weight of the magnesium obtained due to the added mass of the oxide layer, it would not affect the final molar mass of magnesium calculated.

To learn more about "molar mass", visit: https://brainly.com/question/837939

#SPJ11