why does sound get softer the farther you are from a speaker?

Ray could use Metal bar 1 to find out if Metal bar 2 is a magnet by bringing them close to each other. If Metal bar 2 is a magnet, it will be attracted to Metal bar 1.

Ray can also try to move Metal bar 1 along the length of Metal bar 2. If Metal bar 2 is a magnet, it will induce a magnetic field in Metal bar 1, causing it to experience a force as it moves. Alternatively, when Ray moves Metal bar 1 along the length of Metal bar 2, he would observe a force acting on Metal bar 1 as it moves. This is because the magnetic field produced by Metal bar 2.

To know more about Metal bar, here

brainly.com/question/31331801

#SPJ4

The correct statement is " Negative charge flows from the smaller sphere to the larger sphere until the electric potential of each sphere is the same." The correct Option (E).

When the two spheres are connected with a conducting wire, the negative charge will flow from the smaller sphere to the larger sphere until the electric potential of each sphere is the same. This is because the electric potential at a point in space is proportional to the amount of charge present at that point and inversely proportional to the distance from the point to the center of the charged sphere.

Option (A) is not true because charge will flow due to the difference in potential between the two spheres.

Option (B) is not true because the electric field at the surface of each sphere will not necessarily be the same after charge flows.

Option (C) is not true because the electric potential at a point in space is the same for all charged conductors connected by a wire.

Option (D) is not true because the negative charge will flow from the smaller sphere to the larger sphere, not the other way around.

Therefore, The correct answer is option E.

To learn about capacitance click:

brainly.com/question/28445252

#SPJ4

Two conducting spheres of different radii with each negative charge connected with a conducting wire, Negative charges flow from the smaller sphere to the larger sphere until the potential becomes the same. Thus, option E is correct.

The potential V = kQ / r,  Potential and charge are directly proportional to each other, more potential gives more negative charge. More negative charge gives lower potential. The potential always flows from a lower to a higher potential. Thus the negative charge flows from the smaller sphere to the larger sphere to equal the potential.

Thus, the correct option is E.

Learn more about the Electric potential :

https://brainly.com/question/30629127

#SPJ4

If the plate separation is doubled while the battery remains connected, the potential difference between the plates remains the same.  the correct option is E.

The potential difference, also known as voltage, is a measure of the difference in electric potential energy between two points in an electrical circuit. It is defined as the work done per unit charge in moving a positive test charge from one point to another against the electric field. The unit of potential difference is the volt (V). A potential difference of one volt is defined as the energy required to move one coulomb of charge between two points in a circuit, against the electric field, and is often represented as V = W/Q, where V is voltage, W is work, and Q is charge.

Option (A) The electric charge on the plates is doubled is not true because the charge on the plates is determined by the capacitance and the potential difference between the plates, both of which remain constant when the plate separation is doubled while the battery remains connected.

Option (B) The electric charge on the plates is halved is not true because the charge on the plates is determined by the capacitance and the potential difference between the plates, both of which remain constant when the plate separation is doubled while the battery remains connected.

Option (C) The potential difference between the plates is doubled is not true because the potential difference between the plates is determined by the battery emf and the plate separation, but the battery emf is constant and the plate separation has doubled, resulting in the potential difference remaining the same.

Option (D) The potential difference between the plates is halved is not true because the potential difference between the plates is determined by the battery emf and the plate separation, but the battery emf is constant and the plate separation has doubled, resulting in the potential difference remaining the same.

Therefore, the correct option is (E) The capacitance is unchanged.

To learn about capacitance click:

brainly.com/question/28445252

#SPJ4

As you start to turn left, you will feel the right side of the axle D. Push on your right hand vertically up.

When you are walking and holding on to the axle of a spinning bicycle wheel with one hand on either side of the wheel, and you start to turn left, you will feel the right side of the axle push on your right hand towards the left. This is because of the principle of angular momentum. Angular momentum is the measure of the rotational motion of an object around its axis of rotation. In this case, the bicycle wheel is rotating around its horizontal axis, and it has angular momentum. When you turn left, you are changing the direction of the angular momentum of the wheel.

This change in direction of the angular momentum creates a force on the axle, which is transmitted to your hands. The force that you feel on your hands is called the centripetal force, which is the force that keeps the wheel moving in a circular path. This force is directed towards the center of the circle that the wheel is moving in. When you turn left, the direction of the centripetal force changes, and this creates a force on the axle that is transmitted to your hands.

The right side of the axle will push on your right hand towards the left because this is the direction of the force created by the change in direction of the centripetal force. The left side of the axle will push on your left hand towards the right because of the same principle. This is why it is important to hold on to both sides of the wheel when walking alongside a spinning bicycle wheel, as this will help to balance the forces created by the change in direction of the centripetal force. Therefore, the correct answer is option D.

know more about Angular momentum here:

https://brainly.com/question/4126751

#SPJ11

To determine if the equivalent capacitance you calculated (0.62 μF ± 0.04 μF) is consistent with the manufacturer's labeled capacitance (0.5 μF ± 10%), we need to compare the ranges of the two values.

Step 1: Calculate the range for the manufacturer's labeled capacitance.
0.5 μF ± 10% = 0.5 μF ± (0.5 μF * 0.1)
= 0.5 μF ± 0.05 μF
The range is from 0.45 μF to 0.55 μF.

Step 2: Calculate the range for your calculated equivalent capacitance.
0.62 μF ± 0.04 μF
The range is from 0.58 μF to 0.66 μF.

Step 3: Compare the two ranges.
The range for the manufacturer's labeled capacitance is 0.45 μF to 0.55 μF, while the range for your calculated equivalent capacitance is 0.58 μF to 0.66 μF. Since these ranges do not overlap, the calculated equivalent capacitance of 0.62 μF ± 0.04 μF is not consistent with the manufacturer's labeled capacitance of 0.5 μF ± 10%.

To know more about equivalent capacitance:

https://brainly.com/question/30905469

#SPJ11

Utilised to detect certain neuromuscular abnormalities or injuries while monitoring muscle activity.

The amplitude or voltage changes on an electromyography (EMG) signal reflect the electrical activity of the muscle being measured. The EMG signal provides information about the electrical potential difference between two points on the skin, typically overlying a muscle or muscle group.

The amplitude or voltage of the EMG signal is affected by a number of factors, including the number of active motor units, the firing rate of the motor units, and the strength and duration of the muscle contraction. In general, higher amplitude or voltage EMG signals are associated with stronger muscle contractions and/or the recruitment of more motor units.

Changes in the amplitude or voltage of an EMG signal can indicate a number of things, including:

Muscle activity: An increase in EMG amplitude or voltage typically indicates an increase in muscle activity, while a decrease in amplitude or voltage indicates a decrease in muscle activity.

Muscle fatigue: As a muscle fatigues, the amplitude or voltage of the EMG signal may decrease, even if the level of muscle activity remains constant.

Neuromuscular disorders: Certain neuromuscular disorders, such as muscular dystrophy or myasthenia gravis, can affect the amplitude or voltage of the EMG signal.

Muscle injury: Damage to the muscle fibers or nerves innervating the muscle can also affect the amplitude or voltage of the EMG signal.

Overall, changes in the amplitude or voltage of an EMG signal provide important information about the electrical activity of the muscle being measured and can be used to monitor muscle function and diagnose certain neuromuscular disorders or injuries.

To learn more about electrical potential difference visit:

https://brainly.com/question/27091481

#SPJ11

If the two slits were replaced by 20 slits having the same spacing d between adjacent slits in a two-slit experiment with a monochromatic light source, the number of fringes on the screen would increase.

The number of fringes observed in the double-slit experiment is directly proportional to the distance between the two slits. When the distance between the slits is increased, distance between bright fringes on the screen also increases, and the number of fringes observed on the screen decreases. Therefore, if the two slits in a two-slit experiment are replaced by 20 slits having the same spacing d between adjacent slits, the distance between slits will decrease, and the number of fringes observed on the screen will increase.

To know more about monochromatic light , here

brainly.com/question/30887682

#SPJ4

--The complete Question is, Assuming a two-slit experiment with a monochromatic light source, if the two slits were replaced by 20 slits having the same spacing d between adjacent slits, would the number of fringes on the screen increase, decrease, or stay the same?

Hint: Consider the relationship between the number of fringes and the spacing between the slits. --

The phenomenon you're describing, where an accidental path of low resistance bypasses the intended path and allows passage of an abnormally high amount of current, is known as a b) short circuit.

Short circuits occur due to a variety of reasons, including insulation failure, damaged wires, or incorrect wiring.

For instance, if two wires that are meant to be separate accidentally touch each other, a short circuit can occur. Similarly, if a wire's insulation gets damaged, it can come into contact with other wires or conductive surfaces, leading to a short circuit.

When a short circuit occurs, the circuit's protective mechanisms, such as fuses or circuit breakers, may trip to prevent damage. However, if the short circuit is strong enough, it can overload and damage the protective mechanisms as well.

This can cause the circuit to remain live, which can be dangerous and potentially deadly.

Short circuits are common in both household and industrial electrical systems. It is important to address any short circuits promptly to prevent damage to equipment, fires, and injuries. If you suspect a short circuit, it is best to call a professional electrician to diagnose and fix the issue.

To learn more about short circuit, refer below:

https://brainly.com/question/31476272

#SPJ11

In a two-slit interference pattern projected on a screen, the fringes are equally spaced on the screen (c) only for small angles.

In a two-slit interference pattern, the fringes observed on the screen are a result of the constructive and destructive interference of light waves passing through the slits. The spacing of these fringes depends on the angle of incidence.

(a) This is because the path difference between the light waves from the two slits increases as the angle of incidence increases.

(b)  At large angles, the path difference between the interfering waves becomes significantly different, resulting in a noticeable variation in fringe spacing.

(c) In this case, the path difference between the interfering waves is relatively small, which leads to a more uniform spacing of the fringes. This can be explained using the small angle approximation, where sin(θ) ≈ θ for small angles (in radians).

In summary, the fringes in a two-slit interference pattern are more equally spaced for small angles due to the smaller path difference between the interfering waves. As the angle of incidence increases, the path difference becomes more significant, leading to a variation in fringe spacing.The correct answer is c.

Know more about    light waves  here:

https://brainly.com/question/15033563

#SPJ11

The magnitude of the average acceleration of the sports car is 6.87 meters per second squared.

To find the magnitude of the average acceleration of the sports car in meters per second squared, we need to convert the given speed and time values to SI units.

First, let's convert the initial speed of 0 mph to meters per second:

0 mph = 0 m/s

Next, let's convert the final speed of 60 mph to meters per second:

60 mph = 26.8 m/s

Now, let's convert the time of 3.9 seconds to seconds:

3.9 s

To calculate the average acceleration, we use the formula:

average acceleration = (change in velocity) / time

The change in velocity is the difference between the final velocity and initial velocity:

change in velocity = 26.8 m/s - 0 m/s = 26.8 m/s

Plugging in the values, we get:

average acceleration = 26.8 m/s / 3.9 s

average acceleration = 6.87 m/s²

You can learn more about magnitude at: brainly.com/question/30881682

#SPJ11

The tension in string 1 is 19.62 N if the mass M is equal to 6.0 Kg.

To determine the tension in string 1, we need to use Newton's laws of motion and draw a free body diagram of the system. In this case, we have a mass M hanging from two strings, one of which is attached to a fixed point while the other is attached to the ceiling.

The weight of the mass M is acting downwards, with a force of 6.0 kg x 9.81 m/s^2 = 58.86 N. This force is balanced by the tension in the two strings acting upwards.

Let T1 be the tension in string 1, and T2 be the tension in string 2. We can then write the following equations:

T1 + T2 = 58.86 N (balancing the weight of M)
T2 = 2T1 (since the angle between the two strings is 60 degrees)

Substituting the second equation into the first, we get:

T1 + 2T1 = 58.86 N
3T1 = 58.86 N
T1 = 19.62 N

Therefore, the tension in string 1 is 19.62 N. None of the answer options provided match this value exactly, but option 3 (29 N) is the closest.

For more such questions on Tension.

https://brainly.com/question/13397436#

#SPJ11

The tritium nucleus would weigh more than the two neutrons and 1 proton on the other side of the balance scale. B

This is because the tritium nucleus is a specific isotope of hydrogen that contains 1 proton and 2 neutrons, giving it a greater mass than just 2 neutrons and 1 proton.
To determine which side of the balance scale weighs more when you put 2 neutrons and 1 proton on one side and a tritium nucleus (3H) on the other, let's consider the components of the tritium nucleus.
A tritium nucleus consists of 2 neutrons and 1 proton. Therefore, both sides of the balance scale contain the same components, which are 2 neutrons and 1 proton.

Visit here to learn more about tritium nucleus:
brainly.com/question/10343827

#SPJ11

The upper limit on the efficiency of any heat engine operating between two reservoirs is determined by the Carnot efficiency formula. This theoretical efficiency is given by:

Carnot efficiency = 1 - (Tc/Th)

Where Tc is the temperature of the cold reservoir (in Kelvin) and Th is the temperature of the hot reservoir (in Kelvin). Keep in mind that this is the maximum possible efficiency, and real-world heat engines typically have lower efficiencies due to various losses and imperfections.

To know more about heat engine click this link-

brainly.com/question/28034387

#SPJ11

The reference line will be at the position θ=5.0 rev at approximately t = 31.9 seconds.

To solve this problem, we can use the kinematic equations for rotational motion. The equation we need is:

θ = θ₀ + ω₀t + (1/2)αt²

where θ is the final angular position, θ₀ is the initial angular position, ω₀ is the initial angular velocity, α is the angular acceleration, and t is the time. We want to find t when θ = 5 rev, θ₀ = 0, ω₀ = -4.6 rad/s and α = 0.35 rad/s² .

First, we need to convert 5 rev to radians:

θ = 5 rev × (2π rad/rev)

= 10π rad

Plugging in the values we know, we get:

10π = 0 + (-4.6)t + (1/2)(0.35)t²

Simplifying and solving for t using the quadratic formula, we get:

t = 31.9 s or t = -5.6 s

Since time cannot be negative, we reject the negative solution and conclude that the reference line will be at the position θ = 5.0 rev at approximately t = 31.9 seconds.

To know more on angular position

brainly.com/question/13860704

#SPJ4

With standard diagnostic imaging instrumentation, the higher numerical value is typically found in lateral resolution (b).

It depends on the specific type of diagnostic imaging instrumentation being used. Axial resolution refers to the ability to distinguish objects along the direction of the imaging beam, lateral resolution refers to the ability to distinguish objects perpendicular to the imaging beam, and elevational resolution refers to the ability to distinguish objects in the direction of the imaging plane. Different imaging modalities and equipment can have different numerical values for each of these resolutions.

Learn more about  lateral resolution here: https://brainly.com/question/30753488

#SPJ11

If a listener receives sound from a sound reinforcement loudspeaker more than 50 ms after receiving sound directly from the person talking, the two sound signals will be perceived as separate and distinct events.

This is because the human auditory system typically starts to perceive sounds as separate events when the time delay between them is greater than approximately 50 ms. This can result in a phenomenon called the "precedence effect" or "echo," which can negatively affect the clarity and intelligibility of the original sound signal.

Learn more about sound signals https://brainly.com/question/1199084

#SPJ11

If the temperature of the room had been lower, the length of the air column required for resonance would have been shorter.

Step-by-step explanation:

1. When the temperature decreases, the speed of sound in the air also decreases.
2. Resonance occurs when the wavelength of the sound wave matches the specific conditions of the air column.
3. With a lower speed of sound due to the decreased temperature, the wavelength of the sound wave will also be shorter.
4. To maintain resonance with the shorter wavelength, the length of the air column must also be shorter.

In conclusion, a lower temperature would result in a shorter air column length for resonance.

To know more - https://brainly.com/question/26866637

#SPJ11

The force constant k of the spring is approximately [tex]3.125 x 10^8 N/m[/tex].

To determine the force constant k of the spring, we can use the equation for the potential energy of a spring:

[tex]U = (1/2)kx^2[/tex]

where U is the potential energy of the spring, k is the force constant of the spring, and x is the displacement of the spring from its equilibrium position.

When the subway train hits the spring bumper, it compresses the spring by a distance of 0.2 m. We can use the work-energy theorem to find the potential energy stored in the spring:

W = ΔK + ΔU

where W is the work done on the subway train by the spring, ΔK is the change in kinetic energy of the subway train, and ΔU is the change in potential energy of the spring.

At the beginning of the collision, the subway train has a kinetic energy of:

[tex]K1 = (1/2)mv^2 = (1/2)(5.00 x 10^5 kg)(0.5 m/s)^2 = 62,500 J[/tex]

At the end of the collision, the subway train comes to a stop, so its kinetic energy is zero. Therefore, the change in kinetic energy is:

[tex]ΔK = K2 - K1 = 0 - 62,500 J = -62,500 J[/tex]

The potential energy stored in the spring is equal to the work done on the subway train by the spring, so:

[tex]ΔU = W = -62,500 J[/tex]

Using the equation for the potential energy of a spring, we can solve for the force constant k:

[tex]U = (1/2)kx^2[/tex]

[tex]ΔU = (1/2)kx^2[/tex]

[tex]-62,500 J = (1/2)k(0.2 m)^2[/tex]

[tex]k = -2(-62,500 J) / (0.2 m)^2[/tex]

[tex]k = 3.125 x 10^8 N/m[/tex]

for such more questions on   force constant

https://brainly.com/question/25313999

#SPJ11

A meter stick is hung from the ceiling with a string attached to the center. A 3.0 kg mass is hung from the 0.10 m line on the meter stick. A 5.0 kg mass should be hung from the 0.06 m line on the other side of the center.

Balance the meter stick with a 3.0 kg mass hanging from the 0.10 m line, a 5.0 kg mass should be hung from the 0.06 m line on the other side of the center.

This is because the torque due to the 3.0 kg mass on one side of the center is equal and opposite to the torque due to the 5.0 kg mass on the other side, causing the meter stick to be in rotational equilibrium.

Read more about Meter stick.

https://brainly.com/question/15298079

#SPJ11

The statement " A traditional electronic hearing aid is useful only if a person's ear drum and ossicles function to some degree and if the person's cochlea functions at some minimal level" is True because If either of these systems is damaged or not functioning properly, a traditional hearing aid will not be useful.

A traditional electronic hearing aid is designed to amplify sound and deliver it to the ear. However, for the hearing aid to be effective, the ear drum and ossicles must be able to transmit the sound to the inner ear or cochlea. Similarly, the cochlea must be able to detect the sound and send signals to the brain. A typical hearing aid will not be effective if any of these systems is damaged or not operating properly.

It is important for individuals with hearing loss to have their hearing evaluated by a professional to determine the cause and extent of their hearing loss. In some cases, a cochlear implant may be a better option for individuals with severe hearing loss or damage to the ear drum or ossicles. Cochlear implants bypass the damaged portion of the ear and directly stimulate the auditory nerve to provide sound signals to the brain.

For more such questions on hearing aid, click on:

https://brainly.com/question/28448816

#SPJ11

A rigid insulated rod, with two unequal charges attached to its ends, is placed in a uniform electric field E. The rod experiences a net force to the left and a counterclockwise rotation. The correct option is B.

The unequal charges attached to the ends of the rod experience a force due to the uniform electric field. The upper charge experiences a force to the left, while the bottom charge experiences a force to the right.

According to Coulomb's Law, the magnitude of the force between two charges is directly proportional to the product of the charges and inversely proportional to the square of the distance between them. Since the upper charge is twice the magnitude of the bottom charge, the force on the upper charge will be twice as strong.

Therefore, the net force on the rod will be to the left, since the force on the upper charge to the left is greater than the force on the bottom charge to the right. Additionally, the torque on the rod will be counterclockwise since the forces are acting in opposite directions and creating a rotational force.

Thus, the correct option is (B) net force to the left and a counterclockwise rotation.

For more such questions on Net force.

https://brainly.com/question/31045483#

#SPJ11

To find the pressure of a gas given its mole fraction and the total pressure, one can use Dalton's law of partial pressures.

Here are some additional points to consider:

Dalton's law states that the total pressure of a gas mixture is equal to the sum of the pressures of each gas in the mixture, which is proportional to its mole fraction. Therefore, the pressure of a gas can be calculated by multiplying its mole fraction by the total pressure of the gas mixture.

Learn More About mole

https://brainly.com/question/29367909

#SPJ11

The motor boat will require 15.45 seconds to come to a complete stop.

The net force on the boat is the sum of the engine force and the force of the current acting in opposite directions. Therefore, the net force on the boat is,

F_net = F_engine - F_current

F_net = 9,200 N - 12,500 N

F_net = -3,300 N

The negative sign indicates that the net force is acting in the opposite direction to the boat's motion.

We can now calculate the acceleration of the boat using the formula:

a = Fnet / m, where m is the mass of the boat. Plugging in the given values, we get:

a = -3,300 N / 12,000 kg

a = -0.275 m/s², the negative sign indicates that the boat is decelerating.

Finally, we can use the equation of motion, v = u + at, where v is final speed u is initial speed, a and t are acceleration and time.

Rearranging the equation, we get:

t = (v - u) / a

t = (0 - 4.25 m/s) / (-0.275 m/s²)

t = 15.45 s

So, the boat will take 15.45 seconds to stop.

To know more about force, visit,

https://brainly.com/question/12970081

#SPJ4

The body is experiencing negative angular acceleration or angular deceleration.

The temporal rate at which angular velocity changes is known as angular acceleration. The standard unit of measurement is radians per second per second.

The angular acceleration can be determined using the formula:

angular acceleration = (change in angular velocity) / (time taken)

In this case, the change in angular velocity is:

(change in angular velocity) = final angular velocity - initial angular velocity

= (-40 rad/s) - (-20 rad/s)

= -20 rad/s

Assuming that the time taken for this change in angular velocity is not given, we cannot determine the angular acceleration directly using the above formula. However, we can say that the angular acceleration must be negative, as the angular velocity is decreasing (going from -20 rad/s to -40 rad/s). This means that the body is undergoing angular deceleration, or negative angular acceleration.

Learn more about angular acceleration on:

https://brainly.com/question/13014974

#SPJ11

If you were standing between a convex mirror and a plane mirror, you would see a limited number of images of yourself.

The convex mirror would reflect your image in a distorted way, while the plane mirror would reflect your image as it appears in reality.

The images produced by the convex mirror would be smaller and farther away than the image produced by the plane mirror.

The spacing between the multiple images in this case would not be equal, as the convex mirror distorts the reflections.

The spacing would vary depending on the curvature of the convex mirror and the angle at which you are standing relative to the mirrors.

Overall, the combination of a convex and plane mirror would produce a unique and interesting visual effect, with some images being distorted and others being more true to life.

To know more about convex mirror here

https://brainly.com/question/3627454

#SPJ11

The closest option is c. 1 mm, which is smaller than the calculated axial resolution of 3.08 mm.

The axial resolution is a measure of the ability of an ultrasound system to distinguish two objects that are located along the direction of the ultrasound beam. It is determined by the pulse length of the ultrasound wave. The shorter the pulse length, the better the axial resolution.

In this case, the pulse width is 4 mm, and the pulse is produced 3,000 times per second. Therefore, the time between each pulse is 1/3000 seconds or 0.000333 seconds.

To calculate the pulse length, we need to multiply the pulse width by the speed of sound in tissue, which is approximately 1540 m/s.

Pulse length = pulse width x speed of sound in tissue

= 4 mm x 1540 m/s

= 0.00616 meters

The best estimate of the axial resolution is half of the pulse length, since the system can distinguish objects that are located at half the pulse length or farther apart. Therefore, the axial resolution is:

Axial resolution = Pulse length / 2

= 0.00616 meters / 2

= 0.00308 meters or 3.08 mm

So, the answer is not one of the options provided. The closest option is c. 1 mm, which is smaller than the calculated axial resolution of 3.08 mm.

To learn more about sound visit:

https://brainly.com/question/14595927

#SPJ11

The x-coordinate of the center of gravity of the given system of masses is 1.2 m.

Given:

m₁ = 6.0 kg, x₁ = 0.0 m

m₂ = 4.0 kg, x₂ = 2.0 m

m₃ = 5.0 kg, x₃ = 2.0 m

x = (m₁ × x₁ + m₂ × x₂ + m₃ × x₃) / (m₁ + m₂ + m₃)

Substitute values:

x = (6.0 kg ×  0.0 m + 4.0 kg ×  2.0 m + 5.0 kg ×  2.0 m) / (6.0 kg + 4.0 kg + 5.0 kg)

x = (0 + 8 + 10) / 15

x = 18 / 15

x = 1.2 m

Hence, the x-coordinate of the center of gravity of the system of masses is 1.2 m.

To learn more about the center of gravity, here:

https://brainly.com/question/1359722

#SPJ12

When an object repels a plastic rod, it likely has a similar charge as the plastic rod. However, the interaction with a glass rod depends on the charges of both the object and the glass rod.

If the glass rod has an opposite charge, the object repels will attract the glass rod. If the glass rod has a similar charge, the object will repel the glass rod.

An electrical charge is created when wool is rubbed across a plastic rod. This occurs because the plastic rod causes the wool substance to lose some of its electrons. The plastic rod becomes negatively charged, whereas the wool becomes positively charged.

Therefore, an object must also be negatively charged in order to resist the negatively charged plastic rod. This is due to the fact that charged items repel one another.

On the other hand, a glass rod becomes positively charged when it is rubbed against a silk cloth. This occurs as a result of the glass rod losing electrons to the silk fibre. The glass rod then becomes positively charged and the silk substance turns negative.

Learn more about plastic rod here

https://brainly.com/question/14637789

#SPJ11

The average fluid velocity in the 3.50-cm-diameter pipe is approximately 0.87 m/s.

To determine the average fluid velocity in the 3.50-cm-diameter pipe, we can use the formula:

v = (2Q)/([tex]\pi r^2[/tex])

where v is the average fluid velocity, Q is the flow rate, and r is the radius of the pipe.

We can find the flow rate by using the hall voltage measurement and the applied magnetic field. The hall voltage is given as 75.0 mV and the magnetic field is 0.750 T.

The hall voltage is produced due to the movement of charged particles (i.e. ions) in the fluid as it flows through the pipe. The magnetic field causes a force on these charged particles, which results in a potential difference (i.e. voltage) across the pipe. This is known as the hall effect.

The hall voltage is proportional to the product of the magnetic field strength and the flow rate:

VH = KBFQ

where VH is the hall voltage, KB is a constant, BF is the magnetic field strength, and Q is the flow rate.

Solving for Q, we get:

Q = VH/(KBF)

Substituting the given values, we get:

Q = (75.0 x [tex]10^{-3[/tex] V)/(KB x 0.750 T)

We don't know the value of KB, but we can assume that it is constant for the given pipe and fluid conditions. Therefore, we can rewrite the equation as:

Q = C x VH

where C = 1/(KB x 0.750 T).

Now we need to find the constant C. We can do this by using the known flow rate for a given fluid velocity in the pipe. Let's assume that the fluid velocity is 1 m/s. Then the flow rate is:

Q = ([tex]\pi r^2[/tex])v = (π x [tex]1.75^2 * 10^{-4} m^2[/tex]) x 1 m/s = [tex]9.62 * 10^{-5} m^3/s[/tex]

Substituting this into the equation for Q, we get:

C = Q/VH = (9.62 x [tex]10^{-5} m^3/s[/tex])/(75.0 x [tex]10^{-3[/tex] V) = 1.28 x [tex]10^{-3} m^3/(sV)[/tex]
Now we can use this constant to find the flow rate for any given hall voltage. Let's use the given hall voltage of 75.0 mV. Then the flow rate is:

Q = C x VH = [tex](1.28 * 10^{-3} m^3/(sV)) * (75.0 * 10^{-3} V) = 9.60 * 10^{-5} m^3/s[/tex]

Finally, we can use the formula for average fluid velocity to find the answer:

v = (2Q)/(π[tex]r^2[/tex]) = (2 x 9.60 x [tex]10^{-5} m^3/s[/tex])/(π x [tex]1.75^2 * 10^{-4} m^2[/tex]) = 0.87 m/s

For more such questions on Average fluid velocity.

https://brainly.com/question/10709964#

#SPJ11