a person who weighs 830 n is riding a 91-n mountain bike. suppose the entire weight of the rider plus bike is supported equally by the two tires. if the gauge pressure in each tire is 6.80 x 105 pa, what is the area of contact between each tire and the ground?

The attraction occurs because opposite charges attract each other.

The oxygen side of the H2O molecule is attracted to the positively charged plate. This attraction occurs because opposite charges attract each other.

The positive plate has a surplus of positively charged particles, while the oxygen side of the H2O molecule has a partial negative charge due to the shared electrons being pulled towards the oxygen atom.

This partial negative charge is attracted to the positive plate, creating an electrostatic attraction between the two.

Hence, attraction occurs because opposite charges attract each other.

Learn more about "charge": https://brainly.com/question/18102056

#SPJ11

The speed of the electron, after it has accelerated for 10^-9 seconds, is 10^5 m/s. The correct option is C.

Acceleration is the rate at which an object changes its velocity with respect to time. It is a vector quantity, which means it has both magnitude and direction. Mathematically, acceleration is defined as the change in velocity divided by the time taken for that change to occur.

Given:

Acceleration of the electron, a = F/m = 10^-14 N / 9.1 x 10^-31 kg = 1.0989 x 10^17 m/s^2

Time for which electron is accelerated, t = 10^-9 s

Using the equation, âv = at, where âv is the change in velocity, we get:

âv = at = 1.0989 x 10^17 m/s^2 x 10^-9 s = 1.0989 x 10^8 m/s

Therefore, the speed of the electron after it has accelerated for the 10^-9 second is approximately 10^8 m/s, which is closest to option (C) 10^5 m/s.

To learn about Coulomb's law click:

brainly.com/question/506926

#SPJ4

The period of the oscillations will increase by a factor of √(2) or approximately 1.414

The period of an oscillating system, such as a glider attached to springs, is given by the formula:

T = 2π√(m/k)

where T is the period, m is the mass of the glider, and k is the spring constant.

If the mass of the glider is doubled, its new mass will be 2m, and the period will become:

[tex]T' = 2π√(2m/k)[/tex]

Dividing the new period by the original period, we get:

[tex]T'/T = [2π√(2m/k)] / [2π√(m/k)] = √(2)[/tex]

Therefore, the period of the oscillations will increase by a factor of √(2) or approximately 1.414 when the mass of the glider is doubled.

In other words, doubling the mass of the glider will make the oscillations slower, since the glider will have more inertia and will take longer to complete each oscillation.

for such more questions on  oscillations

https://brainly.com/question/29813582

#SPJ11

The statement that is not true about  Common peak clipping is D. The naturalness of the speech is not degraded.

When common peak clipping is applied to speech, the waveform's peaks are truncated, which can result in distortion and a decrease in the naturalness of the speech. This distortion is caused by the introduction of harmonics and other artifacts that were not present in the original signal.

The loss of naturalness is particularly noticeable when the clipping threshold is set too low, as more of the signal will be clipped and greater distortion will be introduced. To minimize the impact on speech naturalness, it's essential to choose an appropriate clipping threshold and apply the technique judiciously.

In summary, common peak clipping can degrade the naturalness of speech due to the distortion introduced by truncating the waveform's peaks. While it can be useful in certain applications, care should be taken to preserve speech quality by selecting an appropriate clipping threshold.The correct answer is d.

Know more about speech    here:

https://brainly.com/question/26157848

#SPJ11

A body's initial position was -20m from the origin and its final position was -10m 1 second later. The body's displacement is 10 meters.

To find the body's displacement, you need to subtract its initial position from its final position.

In this case, the initial position was -20m, and the final position was -10m.

             Displacement = Final Position - Initial Position

             Displacement = (-10m) - (-20m)

             Displacement = (-10m) + 20m

                                     = 20m - 10m

                                     = 10m.

The body's displacement was 10 meters in 1 second.

Learn more about displacement here:

https://brainly.com/question/14422259

#SPJ11

To achieve the smallest possible tangential speed on Earth's surface, you should stand at one of the poles, either the North or the South Pole.

The Earth rotates once per day about its axis, which is perpendicular to the plane of the equator and passes through both the North and South geographic poles. Tangential speed refers to the linear speed of an object moving along the circumference of a circle or a rotating object.

At the poles, you would be at the rotation axis, and your tangential speed would effectively be zero, as you are not moving in a circular path around the Earth's axis. Conversely, at the equator, you would have the highest tangential speed, as you are furthest from the axis and moving in the largest circular path.

In summary, standing at either the North or South Pole would result in the smallest possible tangential speed due to your position directly on Earth's rotational axis. This contrasts with the higher tangential speeds experienced at locations closer to the equator, where the circular path is larger and the distance traveled during Earth's rotation is greater.

For more such questions on Tangential speed.

https://brainly.com/question/4933588#

#SPJ11

Complete Question:

The earth rotates once per day about its axis, which is perpendicular to the plane of the equator and passes through the north geographic pole. Where on the earth's surface should you stand in order to have the smallest possible tangential speed?

The magnitude of the other force is approximately 5.1 N (option 3).

To solve this problem, we can use Newton's second law of motion, which states that the net force on an object is equal to its mass times its acceleration:

ΣF = ma

where ΣF is the net force, m is the mass of the object, and a is its acceleration.

We know that the acceleration of the object is given by:

a = 4.0i - 3.0j

One of the forces acting on the object is given by:

F1 = 2.0i - 1.4j

Let F2 be the other force acting on the object. Then, the net force is given by:

ΣF = F1 + F2

We can use the given acceleration and the equation for net force to solve for F2:

ΣF = ma

F1 + F2 = ma

F2 = ma - F1

F2 = (1.5 kg)(4.0i - 3.0j) - (2.0i - 1.4j)

F2 = 6.0i - 4.5j - 2.0i + 1.4j

F2 = 4.0i - 3.1j

The magnitude of F2 is given by:

|F2| = sqrt[(4.0 N)^2 + (-3.1 N)^2] ≈ 5.1 N

Therefore, the magnitude of the other force is approximately 5.1 N (option 3).

To learn more about magnitude visit:

https://brainly.com/question/15681399

#SPJ11

The most stable nuclei all have around 60 nucleons because B. They have a diameter about equal to the range of the nuclear force. In larger nuclei, like Uranium, the distance between some protons and neutrons may exceed the effective range of the nuclear force, making the nucleus less stable.

The most stable nuclei have around 60 nucleons because their diameter is approximately equal to the range of the nuclear force. The nuclear force is a strong, attractive force that acts between protons and neutrons in the nucleus. This force is short-ranged, meaning it is effective only over a relatively small distance.

In a nucleus with around 60 nucleons, the protons and neutrons are close enough together for the nuclear force to effectively hold the nucleus together. This results in a stable nucleus, as the attractive nuclear force balances the repulsive force experienced between protons due to their positive charge.

Learn more nuclear force about here:
brainly.com/question/4346079

#SPJ11

To calculate the laser power in mW, we can use the formula:
Power = (Number of photons emitted per second) x (Energy per photon)

First, let's convert the wavelength from nanometers to meters:
632 nm = 632 x 10^-9 m

Next, we need to calculate the energy per photon using the formula:
Energy per photon = (Planck's constant) x (speed of light) / (wavelength)

Energy per photon = (6.626 x 10^-34 J s) x (3 x 10^8 m/s) / (632 x 10^-9 m)
Energy per photon = 3.14 x 10^-19 J

Now we can plug in the values:
Power = (8.8 x 10^16/s) x (3.14 x 10^-19 J)
Power = 2.76 W

Finally, let's convert the power to milliwatts:
Power = 2.76 W x 1000 mW/W
Power = 2760 mW

Therefore, the laser power is 2760 mW.

To know more about laser power here

https://brainly.com/question/27853311

#SPJ11

The current in the solenoid is approximately 0.01 A (10 mA), with magnetic field of magnitude 1.00 x 10⁻⁴ T.

To find the current in the solenoid, we can use the formula for the magnetic field inside a long solenoid:

B = μ₀ * n * I

where B is the magnetic field at the center (1.00 x 10⁻⁴ T), μ₀ is the permeability of free space (4π x 10⁻⁷ T m/A), n is the number of turns per unit length (turns/m), and I is the current we want to find.

First, we need to calculate the number of turns per unit length (n):

n = total turns / length = 1000 turns / 0.400 m = 2500 turns/m

Now, we can rearrange the formula to find the current (I):

I = B / (μ₀ * n)

I = (1.00 x 10⁻⁴ T) / (4π x 10⁻⁷ T m/A * 2500 turns/m)

I ≈ 0.01 A

So, the current in the solenoid is approximately 0.01 A (10 mA).

For more such questions on Solenoid.

https://brainly.com/question/13865186#

#SPJ11

A CCD camera is equipped with a lens with constant focal-length. When the f-number is decreased:

a) The aperture increases. This is because the f-number is the ratio of the focal length to the diameter of the aperture, so decreasing the f-number means increasing the diameter of the aperture.

b) The depth of field decreases. This is because the depth of field is inversely proportional to the f-number, so decreasing the f-number means decreasing the depth of field.

c) The intensity of light reaching the sensor increases. This is because the f-number is the ratio of the focal length to the diameter of the aperture, so decreasing the f-number means increasing the diameter of the aperture. This allows more light to reach the sensor.

d) The appropriate exposure time decreases. This is because the intensity of light reaching the sensor increases as the f-number decreases, so the sensor requires less time to capture the same amount of light. Therefore, the exposure time can be decreased to prevent overexposure of the image.

To know more about  lens and focal length, please click on:

https://brainly.com/question/31097794

#SPJ11

Answer:

true

Explanation:

have a good day ml

The particle model of light, also known as the corpuscular theory, proposes that light is composed of discrete particles, or photons, that travel in straight lines and interact with matter through collisions.

This model was developed by Isaac Newton and was used to explain the reflection and refraction of light.

On the other hand, the wave model of light proposes that light is composed of waves that travel through a medium, such as the electromagnetic field.

This model was developed by James Clerk Maxwell and was used to explain phenomena such as interference, diffraction, and polarization of light.

Both models have their strengths and limitations, and the current understanding of light incorporates elements from both models, known as wave-particle duality. This theory proposes that light exhibits characteristics of both waves and particles depending on the context of the observation.

To learn more about diffraction, refer below:

https://brainly.com/question/12290582

#SPJ11

The spring constant is equal to the force applied divided by the displacement from equilibrium.

We can use Hooke's law to calculate the spring constant of the spring:

F = -kx

where F is the force applied to the spring, x is the displacement from equilibrium, and k is the spring constant.

Since the spring is ideal, it is assumed that its mass is negligible, so we can consider it as a massless object.

Assuming that the force F stretches the spring a distance x, we can rearrange Hooke's law to solve for k:

k = -F/x

Therefore, the spring constant is equal to the force applied divided by the displacement from equilibrium.

Learn more about spring constant

brainly.com/question/14159361

#SPJ11

For an ideal gas, two variables are directly proportional to each other (if all other conditions remain constant) are P and n; P and T. The correct option is B. 2 and 3 only.

In an ideal gas, the relationship between the variables can be described using the ideal gas law, which is represented by the equation PV = nRT, where P is pressure, V is volume, n is the amount of gas in moles, R is the ideal gas constant, and T is temperature.

1. P and V: According to Boyle's Law, if temperature and the amount of gas remain constant, the pressure of an ideal gas is inversely proportional to its volume (P ∝ 1/V). This means that as pressure increases, volume decreases, and vice versa.

2. P and n: When the volume and temperature remain constant, the pressure of an ideal gas is directly proportional to the amount of gas in moles (P ∝ n). As the amount of gas increases, so does the pressure.

3. P and T: According to Gay-Lussac's Law, if the volume and the amount of gas remain constant, the pressure of an ideal gas is directly proportional to its temperature (P ∝ T). As the temperature increases, so does the pressure.

Thus, only options 2 and 3 show a direct proportionality between the variables, making the correct answer B (2 and 3 only).

For more such questions on Ideal gas.

https://brainly.com/question/31463642#

#SPJ11

The most likely effect of installing an electric transformer with two coils on an electrical wire is that the voltage carried on the wire will decrease.

What is the most likely effect of installing an electric transformer with two coils on an electrical wire?

The device shown in the image is an electric transformer with two coils. Transformers are used to change the voltage of an alternating current (AC) in a power transmission system. The primary coil is connected to the power source, and the secondary coil is connected to the load.

The most likely effect of installing a transformer on an electrical wire is that the voltage carried on the wire will decrease. When the wire is connected to the primary coil of the transformer, the alternating current flowing through the wire produces a magnetic field around the wire.This magnetic field causes current to flow through the secondary coil, which is connected to the load. The voltage in the secondary coil is proportional to the number of turns in the coil and the voltage in the primary coil.

Therefore, if the number of turns in the secondary coil is less than the number of turns in the primary coil, the voltage in the secondary coil will be lower than the voltage in the primary coil. Conversely, if the number of turns in the secondary coil is greater than the number of turns in the primary coil, the voltage in the secondary coil will be higher than the voltage in the primary coil. In either case, the voltage carried on the wire will decrease as it passes through the transformer.

Therefore, the correct answer is D: The voltage carried on the wire will decrease.

To learn more about electric transformer, visit: https://brainly.com/question/31319378

#SPJ1

The angular position of the top as a function of time is given by

θ(t) = t⁵/4 - 2t³/3 + 5t + 2.

To find the angular position, we integrate the angular velocity function to get the angular displacement, and then add the initial angular position. The angular velocity function is given by:

ω(t) = ∫α(t)dt = ∫(5t³ - 4t)dt = 5t⁴/4 -2t² + c

At ω(0) = 5 rad/s, so c = 5

ω(t) = 5t⁴/4 -2t² + 5

The angular position is

θ(t) = ∫ω(t)dt = ∫(5t⁴/4 -2t² + 5)dt = t⁵/4 - 2t³/3 + 5t + c

As θ(0) = 2rad, so c = 2 rad

θ(t) = t⁵/4 - 2t³/3 + 5t + 2

To know more on angular position

https://brainly.com/question/13860704

#SPJ4

The ball's kinetic energy increases by equal amounts in equal time intervals, not by equal amounts in equal distances.

The ball's kinetic energy increases by equal amounts in equal time intervals. As the ball falls freely, it is affected by gravity, which causes it to accelerate at a constant rate (9.81 m/s²). Due to this acceleration, the ball gains velocity, and therefore, kinetic energy.

Kinetic energy (KE) is given by the equation:

KE = 0.5 * m * v²

Where m is the mass of the ball and v is its velocity. Since the ball is accelerating constantly due to gravity, its velocity increases linearly with time. The increase in velocity leads to a quadratic increase in kinetic energy with respect to time. Therefore, the kinetic energy increases by equal amounts in equal time intervals.

However, the kinetic energy does not increase by equal amounts in equal distances. As the ball falls, its velocity increases, causing the distance it travels in each time interval to also increase. Since the kinetic energy is dependent on the velocity squared, the increases in kinetic energy for equal distances will not be the same.

Learn more about velocity:

https://brainly.com/question/25749514

#SPJ11

When the sun becomes a red giant, the earth will fall into the sun because the force of gravity will increase.

When the sun becomes a red giant, it will exert a greater force of gravity on the earth, such that the earth can be swallowed by the sun.

Thus, the transition of sun into the red giant will result in making all the planets, a part of the sun, by engulfing them. This is because, the gravitational force of attraction of the sun will increase to a greater extent and so the planets will be attracted inwards the sun.

To learn more about red giant, click:

https://brainly.com/question/11362498

#SPJ4

Nothing keeps asteroids moving. The Sun’s force deflects their paths but is not needed to keep them moving. From Newton’s 1st Law, an object that is moving tends to stay moving at constant speed in the same direction, unless a force acts on it. So, once set in motion, an asteroid in outer space just keeps moving.

The frequency criterion for two sinusoidal tones to be perceived as two separate tones, with no roughness or beating, is that their frequencies should differ by more than the critical bandwidth, which is approximately 15-20% of the lower frequency.

This criterion ensures that the two tones are far enough apart in frequency so that our auditory system can distinguish them without experiencing roughness or beating effects.

A pure tone, sometimes known as a sinus tone, is a TONE having a single FREQUENCY. It often comes from a sine wave oscillator or a computer and has the waveform of a sine wave.

for more information on sinusoidal tones: https://brainly.com/question/24336803

#SPJ11

Bandura suggests that violence can be learned through observation and imitation of aggressive models. This theory, known as social learning theory, proposes that aggressive behavior is acquired through the modeling of others, as well as through reinforcement and punishment.

In contrast, Freudian theory suggests that violence arises from unconscious impulses and drives, such as the death drive or aggression drive. According to Freud, these drives can lead to violent behavior if they are not properly sublimated or redirected.

While both Bandura and Freud offer different explanations for the origin of violence, Bandura's theory emphasizes the role of social learning and environmental factors, whereas Freud's theory focuses on internal unconscious processes. Both theories can help us understand why some individuals may engage in violent behavior, and may offer different strategies for prevention and intervention.

To know more on Freudian theory

https://brainly.com/question/17376809

#SPJ4

As the plunger moves away, the gas molecules bouncing elastically off the plunger will also move away from the plunger in various directions.

The force exerted by the plunger on the gas molecules will cause them to gain momentum, resulting in an increase in their kinetic energy.

Eventually, the gas molecules will collide with other gas molecules, transferring their energy and momentum to them, causing a chain reaction that will result in the propagation of pressure waves throughout the gas.

Therefore, gas molecules that are elastically rebounding off the plunger will flow in different directions away from the plunger as it recedes.

Learn more about "gas molecules": https://brainly.com/question/25290815

#SPJ11

The application of maximal voltage in the isolated skeletal muscle will recruit all the muscle fibres.

The neuromuscular junction allows transmission of signals to motor units that further transmit the singal inside the cell of skeletal muscle. The depolarization, repolarization and hyperpolarisation of nerves are the associated features that lead to changes.

The subsequent effect is release of calcium ions from sarcoplasmic reticulum which initiates biochemical pathways involving changes in protein structure. The locomotory proteins are further activated leading to contractility in muscles.

Learn more about skeletal muscles -

https://brainly.com/question/12252128

#SPJ4

The molar mass of the gas: 32.0 g/mol.

1. Convert the volume: You have a volume of 2.00 dm³, which needs to be converted to m³. The conversion factor is 1 dm³ = 10⁻³ m³. So, V = 2.00 dm³ × 10⁻³ m³/dm³ = 2.00 × 10⁻³ m³.

2. Find the number of moles (n) using the ideal gas equation, PV = nRT:
- P (pressure) = 1.01 × 10⁵ Pa
- V (volume) = 2 × 10⁻³ m³ (from step 1)
- R (gas constant) = 8.31 J/(mol·K)
- T (temperature) = 303 K

Plug in these values and solve for n:
(1.01 × 10⁵)(2 × 10⁻³) = n(8.31)(303)
n = 0.0802 mol

3. Find the molar mass (M) of the gas using M = m/n:
- m (mass) = 2.567 g
- n (moles) = 0.0802 mol (from step 2)
M = 2.567 g / 0.0802 mol = 32.0 g/mol

For more such questions on Molar mass.

https://brainly.com/question/7585012#

#SPJ11

Two permanent magnets can attract or repel. Hence option D is correct.

Magnetic force is a force of attraction or repulsion between two magnetic pole or it is force experienced by a charge q when it is placed in magnetic field. Magnetic force in terms of pole strength is given by,

F = μ₀/4π × (m₁m₂÷r²)....

this equation gives the force between two straight magnet having m₁ and m₂ as their pole strength. r is the distance between two magnets and μ₀ is permeability of the free space. this equation is analogous with the coulomb's law which gives the force between two charges.

When two permeant magnet is placed on the horizontal surface, they can attract or repel each other depends on orientation of each with respect to other (like poles repeal while opposite attract ).

Hence option D is correct.

To know more about Magnet :

https://brainly.com/question/2841288

#SPJ4.

A dark fringe, also known as a minima, is a phenomenon observed in wave interference patterns.

A dark fringe, also known as a minima, is a phenomenon observed in wave interference patterns, such as those produced in a double-slit experiment. In these experiments, light waves pass through two slits, and their interference creates a pattern of alternating bright and dark fringes on a screen or detector.

A dark fringe, or minima, occurs when the light waves destructively interfere with one another, resulting in a reduction or cancellation of the light's intensity at that particular point.

This destructive interference happens when the difference in the path lengths of the light waves is equal to an odd multiple of half the wavelength (λ) of the incident light. In other words, when the path difference is (2n+1)λ/2, where n is an integer, a dark fringe will form.

To observe a dark fringe, follow these steps:

1. Set up a double-slit experiment with a coherent light source and a screen or detector.
2. Measure the distance between the slits (d) and the distance from the slits to the screen (L).
3. Calculate the wavelength (λ) of the incident light using the formula λ = (2d * sinθ) / (m), where θ is the angle between the central bright fringe and the dark fringe in question, and m is the order of the fringe (integer).
4. Identify the positions where the path difference is equal to an odd multiple of half the wavelength (λ), using the formula (2n+1)λ/2.
5. Locate the dark fringes, or minima, on the screen where the light intensity is minimized due to destructive interference.

By understanding the principles behind the formation of dark fringes or minima, you can analyze interference patterns and learn about the properties of light and its wave nature.

Learn more about dark fringe:

https://brainly.com/question/27548790

#SPJ11

The object that reaches the bottom of the ramp first is the sphere that rolls down without slipping. This is because the sphere has both translational and rotational kinetic energy, while the block only has translational kinetic energy.

When the sphere rolls down the ramp, it gains both translational kinetic energy, which is the energy of its center of mass moving forward, and rotational kinetic energy, which is the energy of its rotation around its center. The block, on the other hand, only gains translational kinetic energy, as it does not have the ability to rotate like the sphere does.

Since the sphere has more kinetic energy than the block, it will reach the bottom of the ramp first. This is because kinetic energy is directly proportional to velocity, and the sphere's greater kinetic energy will translate to a higher velocity.
In addition, it is important to note that the absence of friction on the block's ramp is not a factor in determining which object reaches the bottom first, as it only affects the block's acceleration down the ramp, not its final velocity at the bottom.

For more such questions on kinetic energy  visit:

https://brainly.com/question/8101588

#SPJ11

If you shoot a single photon through two slits to hit a screen, it can exhibit wave-like behavior and create an interference pattern on the screen. This phenomenon is known as the double-slit experiment and is a fundamental concept in quantum mechanics.

The wave-particle duality of photons means that they can behave both as particles and waves. When a single photon is shot through the two slits, it can pass through both slits simultaneously and create a wave-like pattern that interferes with itself. This interference creates a series of bright and dark fringes on the screen, which is known as the interference pattern.

The interference pattern is a result of the wave nature of the photon and its ability to interfere with itself. This phenomenon is not observed in classical physics and is unique to the quantum world.

The double-slit experiment has been used to study the properties of light and other subatomic particles. It has also played a significant role in the development of quantum mechanics and the understanding of the nature of reality at the atomic and subatomic level.

In summary, shooting a single photon through two slits to hit a screen can exhibit wave-like behavior and create an interference pattern due to the wave-particle duality of photons. This phenomenon is known as the double-slit experiment and has been used to study the properties of light and other subatomic particles.

For more such questions on Double-slit experiment.

https://brainly.com/question/28108126#

#SPJ11

Approximately 50 pounds of M112 would be needed to breach the 5-foot thick dense concrete wall.

To breach a 5-foot thick dense concrete wall utilizing an internal charge placed in the center of the target, it would depend on the specific type of concrete being used and the desired size of the breach.

However, it is generally recommended to use a minimum of 10 pounds of M112 explosive for every foot of concrete thickness.

Therefore, in this instance, 5 feet of dense concrete wall would need to be breached with roughly 50 pounds of M112.

Learn more about "concrete": https://brainly.com/question/28903866

#SPJ11